1,760
edits
Changes
Created page with "Category: OPS535Category: OPS535-LabsCategory: rchan =OPS535 Lab 3 (using Virutal Lab)= == Objectives == * Design the algorithm for setup and configure an OpenLDAP..."
[[Category: OPS535]][[Category: OPS535-Labs]][[Category: rchan]]
=OPS535 Lab 3 (using Virutal Lab)=
== Objectives ==
* Design the algorithm for setup and configure an OpenLDAP server based on [[OPS535-lab-ldap | Lab 3 LDAP lab]]
* Create remote administration script(s) using bash/ansible based on your algorithm
* Deploy the remote administration scripts using bash/ansible on your Seneca VM4 in the OPS535 Virtual Lab
==Pre-Requisites==
:* Has access to Seneca VPN, and matrix.senecacollege.ca
:* Complete the collection of baseline information on your assigned VMs (VM1, VM2, VM3, and VM4)
:* Complete the [[OPS535-lab-ldap | Lab 3 - LDAP lab]] on your home VMs
:* Setup and configure private network for your assigned VMs in the OPS535 Virtual Lab
:* Configure VM1 as your control workstation for performing remote administration tasks on VM[2-4]
==Investigation 1: Algorithm for setup and configure an OpenLDAP server==
==Investigation 2: Scripts for remote deployment of an OpenLDAP server==
=== Task 1 ===
Based on [[OPS535-lab-nfs|Lab 2 - NFS lab]], write a bash script named "lab2-nfs-setup.bash" to perform the following tasks on VM3 (co-rns)
* move the network interface ens224 from firewalld's public zone to internal zone
* install the nfs-utils rpm package if it has not already been installed
* create an nfs share directory named '/nfs-pub' with mode '1777'
* update the /etc/exports as required in [[OPS535-lab-nfs|Lab 2 - NFS lab]]
* enable nfs-server service if has not already been enabled
* start nfs-server service if has not already been started
* update firewalld's internal zone to allow nfs service
* update firewalld's internal zone to allow nfs3 server service
* update firewalld's internal zone to allow rpc-bind service
* save the script to ~student/ops535/lab2/scripts/lab2-nfs-setup.bash
=== Task 2 ===
Create an ansible playbook named "config-nfs.yml" to perform the same tasks as mentioned in task 1.
* save the ansible playbook to ~student/ops535/lab2/playbook/config-nfs.yml
* Run the playbook and capture the output to a file named lab2_inv3_task2.txt in the directory ~student/ops535/lab2/log/
==Completing the Lab==
Follow the instructions on blackboard to submit the lab by the due date.
=OPS535 Lab 3 (using Virutal Lab)=
== Objectives ==
* Design the algorithm for setup and configure an OpenLDAP server based on [[OPS535-lab-ldap | Lab 3 LDAP lab]]
* Create remote administration script(s) using bash/ansible based on your algorithm
* Deploy the remote administration scripts using bash/ansible on your Seneca VM4 in the OPS535 Virtual Lab
==Pre-Requisites==
:* Has access to Seneca VPN, and matrix.senecacollege.ca
:* Complete the collection of baseline information on your assigned VMs (VM1, VM2, VM3, and VM4)
:* Complete the [[OPS535-lab-ldap | Lab 3 - LDAP lab]] on your home VMs
:* Setup and configure private network for your assigned VMs in the OPS535 Virtual Lab
:* Configure VM1 as your control workstation for performing remote administration tasks on VM[2-4]
==Investigation 1: Algorithm for setup and configure an OpenLDAP server==
==Investigation 2: Scripts for remote deployment of an OpenLDAP server==
=== Task 1 ===
Based on [[OPS535-lab-nfs|Lab 2 - NFS lab]], write a bash script named "lab2-nfs-setup.bash" to perform the following tasks on VM3 (co-rns)
* move the network interface ens224 from firewalld's public zone to internal zone
* install the nfs-utils rpm package if it has not already been installed
* create an nfs share directory named '/nfs-pub' with mode '1777'
* update the /etc/exports as required in [[OPS535-lab-nfs|Lab 2 - NFS lab]]
* enable nfs-server service if has not already been enabled
* start nfs-server service if has not already been started
* update firewalld's internal zone to allow nfs service
* update firewalld's internal zone to allow nfs3 server service
* update firewalld's internal zone to allow rpc-bind service
* save the script to ~student/ops535/lab2/scripts/lab2-nfs-setup.bash
=== Task 2 ===
Create an ansible playbook named "config-nfs.yml" to perform the same tasks as mentioned in task 1.
* save the ansible playbook to ~student/ops535/lab2/playbook/config-nfs.yml
* Run the playbook and capture the output to a file named lab2_inv3_task2.txt in the directory ~student/ops535/lab2/log/
==Completing the Lab==
Follow the instructions on blackboard to submit the lab by the due date.