198
edits
Changes
→Known Bugs and Features
==Enable Headless Mode On Windows = Sample ={{Admon/important| Note | If you are using a Windows OS you will need to remove the .txt file extension on the headless file Static Configuration ===.[http://www.ehow.com/how_6394953_create-file-extension.html More information on removing file extensions on eHow]}}Insert the SD card into your system. Only the boot filesystem will be made available, because Windows will not be able to read other partitions on the card. Create a file named "headless" on that partition
There are two possible configurations for Headless Mode "DHCP" configuration and "Static" configuration.
== DHCP Configuration ==
If you would like to configure the Raspberry Pi to use DHCP, ''leave the "headless" file empty'', and the Raspberry Pi should be assigned an IP Address dynamically.
====Optional Configuration====
If "RESIZE" is in the "headless" file, the root filesystem will be expanded to the maximum size of the sd card via the service rootfs-resize. If "SWAP"(requires the value in megabytes) exists in the "headless" file, a swap file will be created of the specified size, and then activated.
RESIZE
SWAP=[Size of swap in megabytes]
====How do I find my IP Address? ====
Once Headless Mode has been Enabled, and the Raspberry Pi has finished booting, the IP Address of the Raspberry Pi will be read out through the speakers or headphones that are connected to the Raspberry Pi. Additionally, the IP Address will be flashed through the LED on the Raspberry Pi soon after the IP Address is read through the speakers.
1 - 9 short flashes indicate the digits 1 - 9
10 short flashes indicate the digit 0
a long flash indicates an octet separator (dot)
a brief pause separates digits
[https://github.com/ctyler/ip-info/blob/master/README.md For more information about IP Address reading and IP Address flashing, click here]
== Static Configuration ==
If you would like to set a static, non-changing, IP Address on your Raspberry Pi, you will need to modify the "headless" file, adding an IP Address, Gateway, and Netmask, to the file for the configurations to work properly(see samples configs below).
====Required Configuration====
IPADDR=[IP Address of Raspberry Pi]
NETMASK=[Mask to define network subnet]
GATEWAY=[IP Address of router/gateway]
====Optional Configuration====
If "RESIZE" is in the "headless" file, the root filesystem will be expanded to the maximum size of the sd card via the service rootfs-resize. If "SWAP"(requires the value in megabytes) exists in the "headless" file, a swap file will be created of the specified size, and then activated.
RESIZE
SWAP=[Size of swap in megabytes]
= Sample Headless Mode Configurations =
Below are sample configurations, they may require you to enter valid ip information specific to the network you are running it on.
====Static Configuration(without rootfs resizing or swap creation)====
IPADDR=192.168.1.105
NETMASK=255.255.255.0
GATEWAY=192.168.1.1
== ==Static Configuration(with rootfs resizing and swap creation)==== IPADDR=192.168.1.105 NETMASK=255.255.255.0 GATEWAY=192.168.1.1 RESIZE SWAP=512 ====Dynamic Configuration(with rootfs resizing and swap creation)==== RESIZE SWAP=512 = SSH to The Headless Mode is enable how do I find out what my ip-address? Pi = Default User: root Default Password: raspberrypi ssh root@{ip_address} =Known Bugs and Features =After you have enabled headless mode with either the DHCP configuration or Static ====Two IP configurationAddresses====When switching in between Headless Mode Configuration states, static ip to dynamic ip, the or dynamic ip address that has been assigned to Raspberry Pi static ip, both IP Addresses from each configuration will be played through active for the speakers "'''2 minutes'''" after single boot, until a reboot takes place. ====Graphical Mode Not Disabled====Headless Mode does not disable X, and can run in both Run Level 3 or 5. This means that if you have powered the Raspberry Piare not planning on using X while in Headless Mode, "'''30 seconds'''" after the ip information has been played it will also flash your ip address through Pi's LED lightsyou should switch to Run Level 3 to save memory.