OPS245 Lab 5

LAB PREPARATION

Monitoring Disk Space can fix problems before they become a crisis (like running low on hard disk space). We will use LVM to easily resize Linux file-systems.

Linux system administrators need to schedule Linux shell scripts and commands (via crontab) to automatically run in order to be more productive.

Purpose / Objectives of Lab 5

The purpose of this lab is to demonstrate how a Linux system administrator can monitor hard disk space availability, and to manage file system size via the Logical Volume Manager (LVM) application. This lab will also demonstrate how to manually mount (i.e. connect) and unmount (disconnect) partitions to file system directories, and demonstrate how to have partitions automatically mounted to directories upon Linux system startup.

Main Objectives

• Monitoring Disk Space with utilities such as ssm list, df -h, and du -ah.
• Use the crontab utility to automatically schedule the execution of a shell script to "flag" low disk space.
• Use LVM to resize partitions via command-line utilities.
• Create, partition and format virtual hard disks to increase the size of file systems.
• Manually connect and disconnect directories (mount points) to existing partitions (mount, umount).
• Edit the /etc/fstab file to automatically mount partitions upon Linux server boot-up, and test the configuration prior to Linux server boot-up.

Minimum Required Materials			Linux Command Reference
Solid State Drive	USB key (for backups)	Lab5 Log Book	LVM Information vgs pvs lvs vgdisplay pvdisplay lvdisplay ssm	LVM Management lvextend lvcreate lvreduce pvcreate vgextend	Miscellaneous mount umount df du awk fdisk mkfs /etc/fstab Using crontab

INVESTIGATION 1: MONITORING HARD DISK SPACE

The df and du commands are useful tools for Linux system administrators to flag disk space issues and investigate their causes.

Part 1: Hard Disk Space Utilities

Another essential duty of a Linux system administrator is to anticipate problems and take preventative measures to avoid computer system problems before they occur. An example would be to periodically monitor hard disk space in order to make adjustments before it impacts on system performance.

Therefore, we are going to learn in this section how to monitor disk space activity to help take corrective action.

Perform the following steps:

1. Launch your c7host and centos2 VMs.
2. Switch to your centos2 machine.
3. Open a terminal.
4. Issue the command: df -h
5. Note the disk space usage for the / and /home partitions.
6. If a partition is running out of available space, the Linux System Administrator can reallocate space among partitions or add another disk and grow the file system. The administrator can also investigate the cause of low disk space. Two examples immediately come to mind: excessive use of space from users, and potential penetration from hackers.
7. To investigate excessive disk usage by regular users, you can obtain a total amount of disk usage for that user by issuing the command:
   du -ha ~<username> | more
8. If there is a recurring space usage problem with regular users, the Linux system administrator can impose quotas (caps on disk usage). This method is not taught in this course.
9. The methods to monitor potential penetration to a Linux system are too numerous, and are taught in other courses (for example: SEC520). One method of monitoring potential penetration is use the find command (Note that find relies on the permissions of the user currently running it. Compare the results of running this command with and without sudo):
   find -P / -size +100000k
10. The next section will apply some of these tools we have discussed into a shell script and crontab entry to periodically monitor and contact the system administrator of potential disk space issues (before they become a serious problem).

Bash Shell Scripting Tips: Using awk to Manipulate Text Very useful command for report generation, text file repair, or text and floating-point decimal manipulation. The command mimics a C program, with braces { } that surround the action to perform based on records from a database file matching either test conditions, regular expressions, etc. Fields appear as numbers with $. Examples: awk '{print}' data-file.txt awk -F";" '{print $5,$3}' data-file.txt awk -F"," '$4 >= 10000 {print $1, $2}' salary.txt Crontab (Chronograph Tables) Used to automatically run (as opposed to manually run) scripts, programs, or commands. There are many tables (files), but the main one is: /etc/cron. The crontab command can be used to list, create, modify or remove scheduled jobs in the file. Examples: crontab -e -u user # create/modify crontab -r -u user-name # remove specific user's crontab crontab -l -u username #List current schedules

Part 2: Using crontab to Automatically Alert System Administrator of Low Hard Disk Space

This section focuses on how to automatically run shell scripts without the Linux system administrator being there to issue that shell script. It would be highly unlikely to expect a system administrator to stay up late (eg. 2 a.m.) to manually run a shell script to terminate processes or to re-boot Linux servers. Database files (tables) are used to provide instructions on how frequent shell scripts or commands can be run.

The cron daemon is used to refer to these shell scripts (or other commands or programs) and to run them on a pre-determined basis. The term cron comes from the old word chronograph meaning a special type of watch (actually a stop-watch) to help monitor and schedule routine tasks.

Perform the following steps:

1. Perform this section in your c7host machine
2. Use sudo -i to get temporary root permissions.
3. Change to the /root/bin directory.
4. Download the following shell script by issuing the following command:
   wget https://ict.senecacollege.ca/~ops235/labs/monitor-disk-space.bash
5. Try to understand what this Bash Shell script does (refer to man pages for the awk command), and then run the script as root.
6. Give execute permissions and run this shell script. This script is supposed to notify the root user by email if there are any potential partition size issues.
7. Issue the follow command: mail (if you get an error, install email by issuing the command:
   yum install mailx
   Check to see if there are any mail messages. If there are mail messages, they do not relate to this shell script execution. Remove all mail messages by typing d immediately followed by a mail message number range (eg. to remove all messages. For example, if there are 5 messages, type d1-5 and then press ENTER and enter q to exit the mail application).
8. Edit the monitor-disk-space.bash shell script, and set the ALERT=90 value to ALERT=10. Then save your editing session, and re-run this shell script.
9. Run the mail command. Do you have a mail message? Enter the mail message number to view the message. If there is a message, what is the purpose of this message?
10. Exit from the mail command.
11. The script as it is currently written will send the email to root, but we won't be logged in as root most of the time. Change the ADMIN variable in the script to your own username.
12. Run the script again and make sure the email message gets delivered to your normal user.

In order to automatically run the above-mentioned script periodically, you use the scheduler in Linux called crontab. The term crontab stands for Chronograph Tables, where a chronograph is the old term for a timepiece (the forerunner of the modern stop-watch). You can run the crontab command to schedule commands and shell script to be run in a number of different ways.

11. Quickly view the tutorial about the Using crontab file to understand the purpose of this file and how to basically set up a schedule to run a shell script.
12. Issue the following command to setup a crontab entry for root:
    crontab -e
13. Enter the following line in order to run at 6:00 on the first day of every month:
    0 6 1 * * /root/bin/monitor-disk-space.bash #Runs first day of each month (6:00 am)
14. Save the crontab entry.
15. Confirm that the entry was properly saved by issuing the following command:
    crontab -l

Answer INVESTIGATION 1 observations / questions in your lab log book.

INVESTIGATION 2: MANAGING HARD DISK SPACE USING LVM

An application called LVM is a very useful tool for Linux system administrators to easily manage file systems, in some cases, even when the computer system is running!

LVM (Logical Volume Management) is used to manage hard disk drives / partitions for Linux and Unix systems. LVM provides more flexibility than just partitioning hard disks. Volume Groups are areas used to define Physical Volumes (i.e. hard disks, disk partitions, or other forms of storage devices). Logical Volumes are then used to relate directories (mount points) to a specific physical volume or for a "range" or "span" of physical volumes.

LVM allows more flexibility and growth potential for Linux systems (for example, having Logical volumes span multiple hard disks). CentOS uses LVM by default upon installation. Other Linux distributions may provide the capacity to install LVM,

Graphical programs like system-config-lvm are deprecated, and no longer come bundled with Centos. There are other graphical LVM programs, but are for the KDE desktop environment as opposed to Gnome. Command-line tools such as ssm (System Storage Manager), fdisk, mkfs, pvcreate, lvextend, and lvreduce are sufficient to resize file systems when using LVM.

Part 1: Managing File System Size with Existing Hard Drive

We will now use LVM in order to grow and reduce our file system, using extra unallocated space on our existing (default) virtual hard disk for our centos2 VM.

Perform the following steps:

1. Remain in your centos2 VM for this section.
2. Issue the command: sudo ls /dev/vd*
   
   NOTE: If nothing displays, issue the command: sudo ls /dev/sd* and use that device pathname /dev/sda instead, and notify your instructor when about to run your lab5-check.bash shell script at the end of this lab.
   
   
3. Issue the following command to install the ssm command:
   sudo yum install system-storage-manager
4. Issue the command: ssm list. Take a few moments to note the volume group, physical volume and logical volume sections of the command output.
5. Compare this output from the ssm command with these other lvm commands: sudo lvs, sudo pvs, and sudo vgs. Which method do you prefer to use?
6. Check to see if there is any remaining space on your existing hard disk. Can you see any?
7. You can create a partition by using the fdisk command. Issue the following command:
   sudo fdisk /dev/vda (or fdisk /dev/sda if there is no /dev/vda).
8. At the fdisk prompt, issue the command: p. What does this do?
9. Now issue the commands n (new partition), p (primary partition), 3 (i.e. next available partition number). When prompted for initial block, press enter to accept the default beginning block size, and type: +3G at ending block (create a 3GB partition) and press enter.
10. At the fdisk prompt, issue the command p to review the partition information.
11. Enter the command w to save partition table and exit (ignore WARNING message).

You MUST reboot your centos2 VM
You MUST now reboot your centos2 VM before proceeding!

13. You must restart your centos2 VM to allow changes to take effect.
14. Verify that you created this partition by issuing the following command: sudo fdisk -l /dev/vda
15. Re-issue the ssm command. Do you see a new /dev/vda3 partition under Physical Volumes?
16. To add the newly created partition, you need to add it into LVM to be used. Issue the following command to add the partition into LVM:
    sudo pvcreate /dev/vda3 (or pvcreate /dev/sda3 ) (enter y to proceed - ignore warning)

Check your VG name
Run vgs to determine your Volume Group name. If it is just centos or cl, replace centos_centos2 with centos or cl for the rest of the following commands in this lab.

17. Issue the following command to add your new-created and formatted partition called /dev/vda3 to your volume group:
    sudo vgextend centos_centos2 /dev/vda3
18. Create a new logical volume by issuing the following command:
    sudo lvcreate -L 2G -n archive centos_centos2
19. Format your newly-created partition by issuing the command: sudo mkfs -t ext4 /dev/centos_centos2/archive
20. Issue the ssm list command to view the new physical volume and logical volume information.

Pay attention to syntax
Note that the prefixed "+" or "-" in lvextend and lvreduce will add or subtract from the current size. Omitting these prefixes will set the LV size to what you specified.

21. Reduce the file-size by issuing the command: sudo lvreduce -r -L -0.5G centos_centos2/archive
22. Issue the ssm list command to verify.
23. Increase the file-size by issuing the command: sudo lvextend -r -L +1G centos_centos2/archive
24. Issue the ssm list command to verify.

You can add virtual hard disks for a VM by changing to the Details section for the VM (as opposed to console), click Add Hardware, fill information in the Add New Virtual Hardware dialog box and clicking Finish.

Part 2: Adding Additional Virtual Hard Drives

What if your have noted while monitoring disk space, that you starting to run-out of space on your home file-system, although you do NOT have any available space on your current hard disk? You could obtain an additional hard-drive. We can add a new virtual hard-drive (which will serve as a physical volume to the volume group), and extend the home logical volume to make use of the new available space. Creating virtual hard drives is not only inexpensive, but a great way for students to learn now to simulate growing the size of the file system!

Perform the following steps:

1. Remain in your centos2 VM for this section.
2. Run the following commands and make note of the output of the commands:
   ls /dev/vd*,
   ssm list, and df -h

3. Record the size of the volume group and the amount of free space
4. At the top of your KVM window for centos2, click the view menu and change view from Console to Details .
5. At the bottom left-hand corner, click Add Hardware and add a new storage device of 2GBs, make sure the Bus type is selected using the same type as your first drive that's already there. If your first drive is SATA, IDE, or VirtIO, select that.
6. Click the VM menu again, and return to the console view to access your centos2 VM display.
7. Issue the command: ls /dev/vd*, what has changed?
8. Use fdisk (refer to how to use in Part 1) to create a new single primary partition for /dev/vdb that fills the entire disk, save partition table (accepting default prompts would work and type w to write your changes!), restart your centos2 VM.
9. Format your new vdb1 partition with file type: ext4
10. Now we'll make the new device a physical volume, add it to the volume group by issuing the following commands:
    pvcreate /dev/vdb1 (enter y to proceed - ignore warning)
    vgextend centos_centos2 /dev/vdb1
    
    NOTE: If you experience an error message, issue the ssm list command, and check the volume group name under the "pool" section.
    If the volume group name is different than centos_centos2, then use that volume group name for all remaining commands that use "centos_centos2"
    
    
11. Re-issue the ssm list command to see if there is any change.
12. Issue the following command to extend the logical volume for the home file-system: lvextend -r centos_centos2/home --size +2G
13. Record the size of the volume group and the amount of free space. What has changed and what caused those changes?
14. Issue the ssm list command. Note that your home file-system is now 2GB bigger, and you have not even rebooted your machine since you used fdisk to create a partition!
15. Reboot your centos2 VM
16. Record the LVM Management commands in your lab log-book.

Using the mount command with no arguments displays file-systems that are already mounted. The Linux system administrator can use the mount and umount commands to connect and disconnect different partitions from the file-system to perform maintenance.

Part 3: Manually & Automatically Mount Partitions

We take for granted that a file-system must be mounted (for example, the root partition) in order for a Linux system to be usable upon system start-up. We need to learn how to do this manually by editing or adding an entry in the file system table (/etc/fstab). This file contains entries to mount various file systems automatically upon start-up of the Linux system.

The Linux system administrator also has the ability to manually mount (connect) and un-mount (disconnect) partitions in order to perform maintenance on the file system (for example, un-mounting the /home partition to install software and prevent users from logging in during that process).

Perform the following steps:

1. Perform this part in your centos2 VM.
2. Issue the following command to create a mount-point (directory to connect /dev/dva3 partition to):
   mkdir /archive
3. Issue the following command to mount the partition:
   mount -t ext4 /dev/centos_centos2/archive /archive
4. Use the ls command to view the contents of the /archive directory. What do you see?
5. Issue the mount command (without arguments) to confirm it has been mounted.
6. Unmount the /archive directory by issuing the following commmand: umount /archive
7. Issue the mount command (without arguments) to confirm it has been mounted.

We will now edit the /etc/fstab file in order to have the /dev/vda3 partition automatically mounted to the /archive directory upon system boot-up

8. View the contents of the file-system table /etc/fstab by issuing the following command:
   cat /etc/fstab
9. Issue the following command to add an entry to automatically mount the /archive directory upon bootup:
   sudo echo "/dev/centos_centos2/archive /archive ext4 defaults 1 2" >> /etc/fstab
10. Reboot your centos2 VM so see if the /archive directory is automatically mounted.
    
    Note: You could have also issued the command: mount -a to automatically mount the file-systems contained in the /etc/fstab file without booting the VM (good for testing before trying a reboot).
    
    

Answer the INVESTIGATION 2 observations / questions in your lab log book.

INVESTIGATION 3: Scripting

Under construction...

LAB 5 SIGN-OFF (SHOW INSTRUCTOR)

Time for a new backup!
If you have successfully completed this lab, make a new backup of your virtual machines as well as your host machine.

Perform the Following Steps:

1. Make certain that your c7host and centos2 VMs are running.
2. Switch to your c7host machine.
3. Open a shell terminal, su - into root, and change to the /root/bin directory., open a shell terminal
4. Issue the Linux command: wget https://ict.senecacollege.ca/~peter.callaghan/ops245/labs/lab5-check.bash
5. Give the lab5-check.bash file execute permissions (for the file owner).
6. Run the shell script and if any warnings, make fixes and re-run shell script until you receive "congratulations" message.
7. Arrange proof of the following on the screen:
   

   ✓ centos2 VM:

   • Output from ssm list command.
   • Proof that /archive has been mounted

   ✓ c7host Machine:

   • Proof of creation of the shell script: monitor-disk-space.bash
   • Crontab entry for root account
   • Run the lab5-check.bash script in front of your instructor (must have all  OK  messages)

   ✓ Lab5 log-book filled out.

Practice For Quizzes, Tests, Midterm & Final Exam

1. What is a VG? PV? LV?
2. What is the total size of the "main" VG on your system?
3. How do you create an LV?
4. How do resize an LV?
5. How would you add the disk partition /dev/sdb7 to your volume group "main"?
6. How would you increase the size of the root filesystem by 50 MB?
7. How can you determine if a partition has been mounted onto a system?
8. How can you unmount an existing partition from the file-system?
9. How can you temporarily mount a partition on a file-system?
10. How can you permanently mount a partition on a file-system upon boot-up?
11. What are the separate elements (fields) of the /etc/fstab file?
12. Describe the tools that a Linux system administrator have to monitor disk space usage.