Difference between revisions of "OPS335 FTP Lab"

From CDOT Wiki
Jump to: navigation, search
m (updated host names)
m (Clarifying instruction)
Line 39: Line 39:
 
#Verify that the ftp connection tracking module is installed in your kernel with the "lsmod" command.  If it is not, you'll have to install it with the command: "modprobe nf_conntrack_ftp".
 
#Verify that the ftp connection tracking module is installed in your kernel with the "lsmod" command.  If it is not, you'll have to install it with the command: "modprobe nf_conntrack_ftp".
 
#Start your ftp server.
 
#Start your ftp server.
#From the command line of your vm, create a new file (or several) in /var/ftp/pub.
+
#From the command line of your server, create a new file (or several) in /var/ftp/pub.
 
#Change the ownership of the /var/ftp/pub directory to the user ftp.
 
#Change the ownership of the /var/ftp/pub directory to the user ftp.
 
#At this point you should test your FTP server from other hosts within your intranet. It should allow anonymous users to retrieve files. From a terminal window on the gateway try these activities:
 
#At this point you should test your FTP server from other hosts within your intranet. It should allow anonymous users to retrieve files. From a terminal window on the gateway try these activities:

Revision as of 13:37, 15 April 2015


VSFTP Setup

This lab will show you how to set up an FTP server and provide you with experience identifying configuration parameters that meet your requirements. You'll be using your Centos host as the FTP server and connecting to it from your VMs and from other machines.

Background Information:

FTP uses 2 TCP ports. The first, usually port 21, is used to send commands to the server (ls, cd, get, put, etc.) and to receive command replies from the server. The second, sometimes port 20, is used to send a file to the server during an upload or to receive a file from the server during a download.

  • FTP can work in 2 modes: Active or Passive.
    • In active mode the client connects to the server on port 21. The server then connects back to the client from port 20. In both connections, the ports used on the client are insecure high-numbered ports ( greater than 1023 ).
    • In passive mode the client first connects to the server on port 21 and makes a second connection to a high-numbered port. As with active mode, the ports used on the client are insecure high-numbered ports ( greater than 1023 ).

FTP can be set up so that anonymous users (users without accounts on the server) may download and possibly upload files.
Passive-ftp.pngActive-ftp.png

Configure your VM

  • Power up your PC (the gateway with host name host), login as your user-id, open a terminal window and "su" to root.
  • Check the settings on your firewall. Ensure that you can still use the services you have configured in previous labs.
  • Now make sure you are connected to the Internet. Start Firefox and authenticate yourself into the network.
  • Login to your VM1 and ensure you have the firewall set up to allow the services you have previously configured (e.g. DNS, apache). If those services are not functioning, fix them (or your firewall) now.

Before preceeding to the next part ensure your gateway is working properly and that your server has access to the Internet. Try some of these commands on your VM/guest:

 ping 192.168.X.1
 host cbc.ca

also use lynx from your vm to ensure you can view internal and external web sites.

Set up your FTP Server (Passive Mode)

  • On your Centos host you should not need to install vsftpd. If it is not present, install it.
 yum install vsftpd
  1. Edit the config file (/etc/vsftpd/vsftpd.conf) to implement the following:
    • Anonymous users should be able to login and download any files (permissions allowing) from the directory /var/ftp/pub.
    • Anonymous uploading should not be allowed.
    • Prevent local accounts from logging in.
    • The FTP Greeting Banner should be set to "Welcome to my OPS335 FTP Server".
    • Set the server to listen on IPv4 sockets, not IPv6.
    • Set the maximum number of concurrent client connections to 30.
    • Set the maximum transfer rate for anonymous users to 140300 bytes per second.
    • Set the connection timeout for idle clients to two minutes.
    • Enable file transfer logging.
    • Limit the range of ports passive mode is allowed to use to 14335 to 14935.
  2. You'll now have to modify your firewall to allow NEW tcp connections on port 21, and tcp connections on the same ports vsftp is will use for data connections.
  3. Verify that the ftp connection tracking module is installed in your kernel with the "lsmod" command. If it is not, you'll have to install it with the command: "modprobe nf_conntrack_ftp".
  4. Start your ftp server.
  5. From the command line of your server, create a new file (or several) in /var/ftp/pub.
  6. Change the ownership of the /var/ftp/pub directory to the user ftp.
  7. At this point you should test your FTP server from other hosts within your intranet. It should allow anonymous users to retrieve files. From a terminal window on the gateway try these activities:
    • ftp using the login 'ftp' to your VM, then list and get the file you created.
    • Try logging is as a user that exists on that machine.

Connecting from outside your intranet

  • Now configure your firewall (using iptables) on the gateway machine to allow FTP clients from outside your network (if you did not already do so).
  • Test your firewall by logging into a second PC (try both Windows and Linux) and attempt an FTP connection to your gateway PC. Test the anonymous user's ability to list and get files again.

Set up your FTP Server (Active Mode)

  1. Edit /etc/vsftpd/vsftpd.conf and disable Passive mode, ensure active mode is enabled, and then restart vsftpd.
  2. Add any iptables rules necessary to allow active connections.
  3. Test your firewall by logging into a second PC (try both Windows and Linux) and attempt an FTP connection to your gateway PC. Test both local user as well as anonymous connections.

Log Packets with iptables

  1. On the firewall/gateway add iptables log rules to monitor ftp traffic (control and data) from outside your network in both of the following.
    • INPUT chain of filter table
    • OUTPUT chain of filter table
  2. While monitoring your packets using "tail -f /var/log/messages" - test your firewall logs by connecting from one of your VMs, and then by logging into a second PC (try both Windows and Linux) and attempt an FTP connection to your gateway PC. Test both local user as well as anonymous connections.

Completing the Lab

In completing this lab you have gained experience using a service that has multiple modes. You have practiced researching configuration parameters to find the ones you need. This will be an invaluable skill, as you will not usually have anyone telling you specifically which parameters to set, or what values to set them to.


Exploration questions:

  1. What parameters did you use to force vsftp to use active mode only.
  2. What version number of vsftpd are you using.
  3. What parameters would you set to configure vsftp to use ssl for authentication.
  4. If you wanted to allow your local users to access their files through ftp, what parameters would you set, and what would you set them to?