Difference between revisions of "OPS235 Lab 1 - CentOS7"

From CDOT Wiki
Jump to: navigation, search
 
(481 intermediate revisions by 4 users not shown)
Line 1: Line 1:
[[Category:OPS235]]'''Bold text'''
+
[[Category:OPS235]]
 +
{{Admon/caution|THIS IS AN OLD VERSION OF THE LAB|'''This is an archived version. Do not use this in your OPS235 course.'''}}
 +
 
 
=LAB PREPARATION=
 
=LAB PREPARATION=
 
==Purpose / Objectives of Lab 1==
 
==Purpose / Objectives of Lab 1==
Line 9: Line 11:
  
 
<u>Main objectives</u>:
 
<u>Main objectives</u>:
<br>
 
:* '''Correctly install the CentOS 7 FULL INSTALL DVD''' (not LIVE DVD) on your removable hard disk.
 
  
:* '''Record installation characteristics of CentOS 7 FULL INSTALL''' in a chart (contained in lab2 logbook chart) to compare with other installation methods performed in lab2.
+
* '''Correctly install the CentOS 7 FULL INSTALL DVD''' (not LIVE DVD) on your removable hard disk.
 +
 
 +
* '''Record installation characteristics of CentOS 7 FULL INSTALL''' in a chart (contained in lab2 logbook chart) to compare with other installation methods performed in lab2.
  
:* '''Verify correct settings''' prior to proceeding with host installation stages.
+
* '''Verify correct settings''' prior to proceeding with host installation stages.
  
:* '''Obtain Linux server information after installation''' to create a software asset report for later access.
+
* '''Obtain Linux server information after installation''' to create a software asset report for later access.
  
:* '''Disable Linux Kernel security enhancements''' to allow easier internal networking connections (to be reactivated in a later lab).
+
* '''Disable Linux Kernel security enhancements''' to allow easier internal networking connections (to be reactivated in a later lab).
  
:* Observe that '''Bash Shell Scripts can automate routine tasks'''.
+
* Observe that '''Bash Shell Scripts can automate routine tasks'''.
  
  
==Required Materials / Lab Preparation==
+
==Minimum Required Materials==
{|cellpadding="15" width="100%"
+
{|
  
 
|- valign="top"
 
|- valign="top"
  
|[[Image:blank-cd.png|thumb|left|75px|<b>CentOS 7</b>FULL INSTALL DVD]]
+
| [[Image:blank-cd.png|thumb|left|75px|<b>CentOS 7</b>FULL INSTALL DVD]]
  
| [[Image:harddrive.png|thumb|left|75px|<b>Removable Hard Disk Pack</b> (SATA)]]
+
| [[Image:harddrive.png|thumb|left|75px|<b>Removable Hard Disk Pack</b> (SATA)]]
  
|[[Image:ubs-key.png|thumb|left|75px|<b>USB key</b><br>(for backups)]]
+
| [[Image:ubs-key.png|thumb|left|75px|<b>USB key</b><br>(for backups)]]
  
|[[Image:log-book.png|thumb|left|60px|<b>Lab Log Book</b><br>(labs 1 & 2)]]
+
| [[Image:log-book.png|thumb|left|60px|<b>Lab Log Book</b><br>(labs 1 & 2)]]
  
| width="60%" |{{Admon/tip|Access to Instructions for Lab1|Since you will performing a full install on your computer, you cannot use that computer to simultaneously view instructions while you perform the full install. Here are some suggestions to make this process easier:<ul>  <li>'''Printout Lab1 instructions''' at home prior to performing Lab1</li>  <li>'''Use a smart-phone, notebook, or netbook computer to view lab instructions''' (highly recommended)</li><li>If lab space availability is not an issue, '''use another computer termimal to view lab instructions''' while performing install</li><li>'''Follow step-by-step instructions from your OPS235 instructor''' (if demonstrated by instructor)</li></ul>|
+
| width="40%" |{{Admon/tip|Access to Instructions for Lab1|Since you will performing a full install on your computer, you cannot use that computer to simultaneously view instructions while you perform the full install. Here are some suggestions to make this process easier:<ul>  <li>'''Printout Lab1 instructions''' at home prior to performing Lab1</li>  <li>'''Use a smart-phone, notebook, or netbook computer to view lab instructions''' (highly recommended)</li><li>If lab space availability is not an issue, '''use another computer termimal to view lab instructions''' while performing install</li><li>'''Follow step-by-step instructions from your OPS235 instructor''' (if demonstrated by instructor)</li></ul>|
 
}}
 
}}
 
|}
 
|}
  
  
 +
==My Toolkit (CLI Reference)==
  
==Online Linux Command Online Reference==
+
{| width="100%"
 
 
{|width="100%" cellpadding="15"
 
 
|- valign="top"
 
|- valign="top"
 
|<u>Package Management</u>
 
|<u>Package Management</u>
[http://www.rpm.org/max-rpm/rpm.8.html rpm]
+
[http://www.rpm.org/max-rpm/rpm.8.html rpm]<br>
 +
[http://man7.org/linux/man-pages/man8/yum.8.html yum]
 
|<u>System Information</u>
 
|<u>System Information</u>
  
Line 63: Line 65:
  
 
[http://unixhelp.ed.ac.uk/CGI/man-cgi?grep grep]<br>
 
[http://unixhelp.ed.ac.uk/CGI/man-cgi?grep grep]<br>
[http://man7.org/linux/man-pages/man1/wc.1.html wc]
+
[http://man7.org/linux/man-pages/man1/wc.1.html wc]<br>
|width="60%" |{{Admon/tip|Online Linux Command Review|The following links will allow you to practice Linux commands that you learned from ULI101:<ul> <li>Bash Shell Command-line Editing</li><li>Common Linux Commands</li><li>Using a Text Editor</li><li>Simple Bash Shell Scripting</li></ul>|
+
[http://man7.org/linux/man-pages/man1/pwd.1.html pwd]<br>
 +
[http://man7.org/linux/man-pages/man1/ls.1.html ls]<br>
 +
[http://man7.org/linux/man-pages/man1/more.1.html more]<br>
 +
[http://man7.org/linux/man-pages/man1/file.1.html file]<br>
 +
[http://man7.org/linux/man-pages/man1/wget.1.html wget]<br>
 +
[http://man7.org/linux/man-pages/man1/chmod.1.html chmod]<br>
 +
[http://man7.org/linux/man-pages/man1/scp.1.html scp]<br>
 +
[http://ss64.com/vi.html vi]
 +
 
 +
|width="40%"|{{Admon/tip|Online Hands-on Linux Tutorials (recommended)|The following online tutorial will allow you to practice Linux commands that you learned from ULI101 as well as essential shell scripting skills. Login to your '''Matrix''' account, and issue the pathnames to run the online tutorial in Matrix:<br><ul><li>Using the vi Text Editor:<br>'''/home/murray.saul/vi-tutorial'''<br><li>Linux Basics:<br>'''/home/murray.saul/linux-basics'''</li><li>Shell Scripting - Part I (Scripting Basics):<br>'''/home/murray.saul/scripting-1'''</li></ul>|
 
}}
 
}}
 
|}
 
|}
Line 70: Line 81:
 
=INVESTIGATION 1: CREATE HOST MACHINE (c7host)=
 
=INVESTIGATION 1: CREATE HOST MACHINE (c7host)=
  
 +
For the next 3 investigations, you will learn how to install your Centos Full DVD onto your removable hard disk. You will customize your install to setup several separate partitions:<ul><li>'''/''' (The "root" partition)</li><li>'''/home''' (Store regular user accounts)</li><li>'''/var/lib/libvirt/images''' (store virtual machine images to be created in lab2)</li><li>'''swap'''  partition (Virtual Memory)</li></ul>
  
 +
Make certain to record your observations of this install in the comparison chart for '''c7host''' in your lab2 logbook.
  
 
==Part 1: Start Installation ==
 
==Part 1: Start Installation ==
  
{|width="100%" cellpadding="15"
+
 
 +
 
 +
::'''<u>Host Machine Details:</u>'''
 +
 
 +
::*'''Name:''' c7host
 +
::*'''Boot media / Installation:''' CentOS7 Full Install DVD
 +
::*'''Memory:''' 16GB
 +
::*'''Disk space:''' 250GB (or higher)
 +
::*'''CPUs:''' 1
 +
 
 +
{| width="40%" align="right" cellpadding="10"
 +
|- valign="top"
 +
|colspan="2"|{{Admon/important |You're supposed to use this hard drive only for this course| But if you really need to use it for two courses, and the professor for the other (probably windows)  course will allow it - ask your professor for help with partitioning.}}
 
|- valign="top"
 
|- valign="top"
 
|
 
|
# For reference: <ul><li>Installation Pictures: [ [http://matrix.senecac.on.ca/~murray.saul/ops235/installation/ installation screenshots] ]</li></ul><br>
+
[[Image:lab2-logbook.png|thumb|right|100px|'''comparison chart''' in lab2 logbook.]]
 +
|
 +
[[Image:installation_summary.png|thumb|right|400px|The '''Installation Summary''' screen provides flexibly when configuring to install on your computer. ]]
 +
|}
 +
 
 +
# Refer to this listing of installation screenshots if you need a reference:<br>[ [http://matrix.senecac.on.ca/~murray.saul/ops235/installation/ installation screenshots] ]<br>
 
# Insert your '''removable SATA hard disk''' into the drive tray.
 
# Insert your '''removable SATA hard disk''' into the drive tray.
 
# Set your computer's drive selector switch to '''external''' (a.k.a ''position #4'').
 
# Set your computer's drive selector switch to '''external''' (a.k.a ''position #4'').
 
# Power up the computer and insert the '''CentOS 7 Installation DVD''' into the DVD drive, then power-off computer.
 
# Power up the computer and insert the '''CentOS 7 Installation DVD''' into the DVD drive, then power-off computer.
# Restart the computer, and '''press the function key F10, press ENTER, and specify the device to boot''' (eg. DVD drive).
+
# '''Newer computer models''' are labelled '''HP Z230'''.<br><br>'''NOTES:'''<ul><li>If you are using the '''<u>newer</u>''' model, allow the computer to boot up (<u>without</u> pressing F10 key) to boot from DVD.</li><li>Refer to the comparison chart in lab2 lab logbook, and fill in various installation information for '''c7host''' while you perform the installation (such as time it took to perform a full install, installation options, etc).<br><br></li></ul>
 
 
::'''NOTE:''' Refer to the comparison chart in lab2 lab logbook, and fill in various installation information for '''c7host''' while you perform the installation (such as time it took to perform a full install, installation options, etc).
 
 
 
 
<ol>
 
<ol>
  <li value="5">Select the option '''Test this Media & Install Centos7'''. Your DVD will be checked for defects</li>
+
  <li value="6">Power on the computer again, and after booting from the CD, select from the installation menu: '''Install Centos7'''.<br><br>Note: If you experience unreadable display after you boot into your installed system, you can redo the install, but select from the install menu: ''<u>Troubleshooting</u>'' and then select ''<u>Install in Basic Graphics Mode</u>''.<br><br></li>
  <li>If the check is successful, you will be prompted for a language. In the first screen, select language '''English''' with subselection '''English-Canada''' and then click the '''Continue''' button on the bottom right-hand screen.</li>
+
  <li>Next, you will be prompted for a language. In the first screen, select language '''English''' with subselection '''English-Canada''' and then click the '''Continue''' button on the bottom right-hand screen.</li>
  
 
  <li>The '''Install Summary''' should now appear. This screen allows the installer to customize their Centos7 system prior to installation.</li>
 
  <li>The '''Install Summary''' should now appear. This screen allows the installer to customize their Centos7 system prior to installation.</li>
  <li>Configure the following installation settings from the ''Install Summary Screen'':<br><br><b>DATE & TIME:</b><ul><li>Click on the Map to select Toronto area (you may also select from the drop-down menu section)</li><li>Click the <b>DONE</b> button at the top-right corner to finish and return to the Installation Summary screen.</li></ul><br><b>NETWORK & HOSTNAME:</b><ul><li>Select the default Ethernet connection and click the button on the right-hand side to change the setting from <b>OFF</b> to <b>ON</b>.</li><li>At the bottom right-hand corner type the hostname: <b>c7host</b> (all lowercase letters)</li><li>Review your settings, then click the <b>DONE</b> button at the top-right corner to finish and return to the Installation Summary screen.</li></ul><br><b>SOFTWARE SELECTION:</b><ul><li>Select the software packages labelled: <b>Gnome Desktop</b></li><li>Click the <b>DONE</b> button at the top-right corner to finish and return to the Installation Summary screen.</li></ul><br></li> <li>Although the Centos installtion program can provide suggestions on how to partition your hard disk, you will be customizing partitions for your hard disk. This custom partitioning is important since it will have consequences on future labs that you perform (especially lab2!).</li>
+
  <li>Configure the following installation settings from the ''Install Summary Screen'':<br><br><b>DATE & TIME:</b><ul><li>Click on the Map to select Toronto area (you may also select from the drop-down menu section)</li><li>Click the <b>DONE</b> button at the top-left corner to finish and return to the Installation Summary screen.</li></ul><br><b>NETWORK & HOSTNAME:</b><ul><li>Select the default Ethernet connection and click the button on the top right-hand side to change the setting from <b>OFF</b> to <b>ON</b>.</li><li>At the bottom left-hand corner type the hostname: <b>c7host</b> (all lowercase letters)</li><li>Review your settings, then click the <b>DONE</b> button at the top-left corner to finish and return to the Installation Summary screen.</li></ul><br><b>SOFTWARE SELECTION:</b><ul><li>Select the software packages labelled: <b>Gnome Desktop</b></li><li>Click the <b>DONE</b> button at the top-left corner to finish and return to the Installation Summary screen.</li></ul><br></li> <li>Although the Centos installtion program can provide suggestions on how to partition your hard disk, you will be customizing partitions for your hard disk. This custom partitioning is important since it will have consequences on future labs that you perform (especially for lab2).<br><br>Proceed to '''Part 2''' to customize your partitions.</li>
 
</ol>
 
</ol>
|width="40%"|{{Admon/important |You're supposed to use this hard drive only for this course| But if you really need to use it for two courses, and the professor for the other (probably windows)  course will allow it - ask your professor for help with partitioning.}}<br><br>[[Image:installation_summary.png|thumb|right|650px|The '''Installation Summary''' screen provides flexibly when configuring to install on your computer. ]]
+
 
|}
+
 
 
== Part 2: Custom Partitioning ==
 
== Part 2: Custom Partitioning ==
{|cellpadding="15" width="100%"
+
 
 +
{|width="40%" align="right" cellpadding="10"
 
|- valign="top"
 
|- valign="top"
 
|
 
|
 +
{{Admon/tip|Mount Points and Linux File System Types|Similar to other Operating Systems like windows '''fat''' / '''vfat''' / '''ntfs''' file system types, it is good to know a few common file system types in Linux for comparison:<br><ul><li><b>xfs:</b> &nbsp; Newer filesystem (fast transfer rates for large files, Journaling)</li><li><b>ext4:</b> &nbsp; Newer filesystem supporting large files and Journaling (used in for this lab)</li><li><b>ext2:</b> &nbsp; Stable filesystem popular for databases (no journaling)</li></ul>|
 +
}}
 +
|-
 +
|
 +
[[Image:partition_verification.png|thumb|right|550px|Carefully verify partition mount-names and sizes prior to proceeding with install. Check [http://matrix.senecac.on.ca/~murray.saul/ops235/installation/ installation screenshots] link for verification.]]
 +
|}
 
#From the installation summary screen, click '''Installation Destination'''.
 
#From the installation summary screen, click '''Installation Destination'''.
 
#In the installation destination screen, select the destination option: '''I will configure partitioning''' and then click '''Done'''.
 
#In the installation destination screen, select the destination option: '''I will configure partitioning''' and then click '''Done'''.
#The manual partitioning screen should appear. Change the option '''New mount points will use the following partition scheme''' from '''LVM''' to '''Standard Partition''' (you will not be using LVM for your c7host machine).
+
#The manual partitioning screen should appear.
 
#If you have used your hard disk for previous Linux (Centos) distributions, you should remove them. Click on the distribution, and for each partition, select the partition and click the remove button (minus sign) and confirm deletion.
 
#If you have used your hard disk for previous Linux (Centos) distributions, you should remove them. Click on the distribution, and for each partition, select the partition and click the remove button (minus sign) and confirm deletion.
#It is recommended to rescan the hard disks by clicking on the rescan button (loop symbol).
+
#<span style="background-color:yellow">Change the option '''New mount points will use the following partition scheme''' from '''LVM''' to '''<u>Standard Partition</u>''' (you will not be using LVM for your c7host machine)</span>.
#Before you proceed with creating partitions, let's see the partitions that we need to create for our host computer:<ul><li>Primary Partitions (ext4):<ul><li>'''20GB''' for '''/'''  (i.e. "root")</li><li>'''30GB''' for /home</li><li>'''100GB''' for '''/var/lib/libvirt/images''' </li></ul> </li><li>Swap Partition:<ul><li>'''8GB''' (Note: "swap" must be selected from the drop down menu)</li></ul></li></ul><br>'''NOTE:''' Remember that the sizes are recorded in MB (eg. 20 GB = 20000 MB) and you should multiply GB by a factor of 1024 to get the correct size.<br> (eg. '''20 GB x 1024 = 20480 MB''')<br><br>
+
#Before you proceed with creating partitions, let's see the partitions that we need to create for our host computer:<ul><li>Primary Partitions (ext4):<ul><li>'''30GB''' for '''/'''  (i.e. "root")</li><li>'''40GB''' for /home</li><li>'''100GB''' for '''/var/lib/libvirt/images''' </li></ul> </li><li>Swap Partition:<ul><li>'''16GB''' (Note: "swap" must be selected from the drop down menu)</li></ul></li></ul><br>'''NOTE:''' Remember that the sizes are recorded in MB (eg. 30 GB = 30000 MB) and you should multiply GB by a factor of 1024 to get the correct size.<br> (eg. '''30 GB x 1024 = 30720 MB''')<br><br>
#We will now create the root (/) partition. Click on the add button (plus) sign.<br>
+
#We will now create the root (/) partition. '''Click on the add button (plus) sign'''.<br>
#In the '''Add a New Mount Point''' screen, enter '''/''' as the mount-point (either by typing or selecting from drop-down menu), and enter '''20480''' in for partition size and click '''Add Mount Point''' button.
+
#In the '''Add a New Mount Point''' screen, select '''/''' as the mount-point (either by typing or selecting from drop-down menu), and enter '''30720''' in for partition size and click '''Add Mount Point''' button.
 +
# You will return to the previous dialog box.<br><span style="background-color:yellow">For the '''/''' partition, change the file-system type from '''xfs''' to '''ext4''' and make certain that the Device Type is set to Standard Partition (<u>not</u> LVM). You need to repeat this procedure for the ''/home'' and ''/var/lib/libvirt/images partitions'' as well)</span>.
 
#Repeat the same steps above for the '''/home''' partition and '''/var/lib/libvirt/images''' partition. You need to type the ''/var/lib/libvirt/images'' partition since it does not appear in the drop-down menu.
 
#Repeat the same steps above for the '''/home''' partition and '''/var/lib/libvirt/images''' partition. You need to type the ''/var/lib/libvirt/images'' partition since it does not appear in the drop-down menu.
#Select each of the created partitions, and make certain that the file-system type is changed from '''xfs''' to '''ext4'''.
+
#Recheck each of the created partitions, and make certain that the file-system type is set to ''ext4'' and the Device Type is set to ''Standard Partition''.
#Check that your partition settings are correct (you can ask your instructor or lab monitor to confirm), and then click Done to proceed.
+
#Finally, add a swap partition (Mount Point: swap) for '''16 GB'''.
#A Summary of Changes screen will appear to show the partitioning operations that will be created. Click the '''Accept Changes''' button to proceed with the installation.
+
#Check that your partition settings are correct (you can ask your instructor or lab monitor to confirm), and then click '''Done''' (possibly '''<u>twice</u>''') in order to proceed<br><br><span style="background-color:yellow">'''NOTE:''' If there is an error message associated with your created partitions, you may need to add a '''/boot/efi''' partition (as a new mount). The capacity should be: 2954MB (i.e. 2,954 MB). Once finished, click '''Done'''.<span><br><br>
| width="40%" |{{Admon/tip|Mount Points and Linux File System Types|Similar to other Operating Systems, it is good to know basic characteristics of file system types in Linux to select the best type for your machine:<br><ul><li><b>xfs:</b> &nbsp; Newer filesystem (fast transfer rates for large files, Journaling)</li><li><b>ext4:</b> &nbsp; Newer filesystem supporting large files and Journaling</li><li><b>ext2:</b> &nbsp; Stable filesystem popular for databases (no journaling)</li></ul>|
+
#A Summary of Changes screen will appear to show the partitioning operations that will be created. Click the '''Accept Changes''' and click '''Begin Installation''' in the Installation Summary screen to proceed with the installation.
}}
+
#Start timing your host machine installation.
 +
 
 +
== Part 3: Completing the Installation ==
  
[[Image:partition_verification.png|thumb|right|500px|Carefully verify partition mount-names and sizes prior to proceeding with install. Check [http://matrix.senecac.on.ca/~murray.saul/ops235/installation/ installation screenshots] link for verification.]]
+
{|width="40%" align="right" cellpadding="10"
 +
|- valign="top"
 +
|[[Image:completed.png|thumb|right|500px|This screen indicates that installation is complete. You should remove the install DVD and confirm Centos7 boots from your removable hard drive. ]]
 
|}
 
|}
 
+
#During the installation process, you will required to create a '''root password''' (for administration access) and create a '''regular user account'''. Click on '''Root Password''' and enter your root password. Think of an appropriate password and record that password somewhere in case you forget! An indicator will appear to show you how secure your password is. Retype your root password and click '''Done''' (you may have to click Done <u>twice</u> if your password is not considered to be a strong password).
== Part 3: Completing Installation ==
+
#You need to create a regular user account. This account will be used to graphical log into your host machine. It is never recommended to graphically log into a graphical Linux/Unix system as root. It is better to log into a regular user account, then run a command to login as root (you will learn how to do this later in this lab).
[[Image:completed.png|thumb|right|500px|This screen indicates that installation is complete. You should remove the install DVD and confirm Centos7 boots from your removable hard drive. ]]
+
#Click '''User Creation''' and enter your '''full name''', '''username''', and an appropriate '''password''' (and confirm password). Click '''Done''' to finish (click twice if password is not considered to be a strong password).
 
+
#<span style="background-color:yellow">Remember to record this host installation information in the '''installation comparison chart''' in the lab2 logbook</span>.
#During the installation process, you will required to create a root password (for administration access) and create a regular user account. Click on '''Root Password''' and enter your root password. Think of an appropriate password and record that password somewhere in case you forget! An indicator will appear to show you how secure your password is. Retype your root password and click '''Done''' (you may have to click Done twice if your password is strong).
 
#You need to create a regular user account. This account will be used to graphical log into your host machine. It is never recommended to graphically log into a graphical Linux/Unix system as root. It is better to log into a regualr user account, then run a command to login as root (you will learn how to do this later in this lab.
 
#Click '''User Creation''' and enter your '''full name''', '''username''', and an appropriate '''password''' (and confirm password). Click '''Done''' to finish.
 
#Remember to record this host installation information in the comparison chart in lab2.
 
 
#When installation is complete, you will notice a message at the bottom of the screen stating: '''CentOS is now successfully installed and ready for you to use!'''
 
#When installation is complete, you will notice a message at the bottom of the screen stating: '''CentOS is now successfully installed and ready for you to use!'''
#Click the Reboot button. Your DVD will briefly open in the DVD drive bay. Make certain to remove this installation DVD so that Centos will boot from your hard drive.
+
#Click the Reboot button. Your DVD will <u>briefly</u> open in the DVD drive bay. Make certain to remove this installation DVD so that Centos will boot from your hard drive.
#After the system reboots, login by clicking on your account name and entering the regular user password.<br><br>
+
#After the system reboots, a boot menu should briefly appear, then prompt the user to accept the License Information (this is only a one-time occurrence).<br> In order to accept the license agreement, issue the following keystrokes:<br><br>'''1''' followed by ENTER (to select the license agreement prompt<br>'''2''' followed by ENTER (to accept the license agreement)<br>'''c''' followed by ENTER (to save the selection)<br>'''c''' followed by ENTER (a second time to continue booting into the system)<br><br>
#The last phase of the installation process should now run:<ul><li>Click Accept to confirm you will abide by the License and click Done.</li><li>Accept defaults to participate running KDump application that will report errors to developers for improvements to Centos7.</li><li>Select English as the default input source.</li><li>Quickly view Getting Started Resources, then close the help window.</li></ul><br>
+
#The system should then graphically prompt the user to login with their regular user account. Click on your '''regular user account name''' and '''enter your regular user password'''.<br><br>
#Proceed to Investigation 2 to obtain basic information from your newly installed Centos Host machine.
+
#The last phase of the installation process should now run:<ul><li>Confirm English as the default input source and click '''Next'''.</li><li>Skip the creation of online accounts by clicking '''Next'''.<li>Start using your installed Linux system by clicking '''Start Using CentOS Linux'''.</li></ul><br>
 
+
#Stop timing your installation and note the amount of time that your installation took to perform. Also take the time to fill in the c7host section of the installation comparison chart in your lab2 logbook.
 +
#Open a web-browser and check to see if you can connect to the Internet.<br><br>
  
'''Answer Investigation 1 observations (all parts and questions) in your lab log book.'''
+
=== Turn-Off Screen Saver Lock ===
  
=INVESTIGATION 2: OBTAINING HOST MACHINE SYSTEM INFORMATION=
+
:Your system automatically enables a '''screen-saver''' application which is a useful security tool to prevent unauthorized viewing of information on a terminal after a certain amount of inactivity.
  
 +
:If you find this feature annoying and want to turn it off or adjust the idle time perform the following steps:
 +
:*Click on your '''username at the top right-hand screen'''
 +
:*Select '''Settings''' from the drop-down menu.
 +
:*Click the '''Power''' icon located in the ''Settings'' Dialog Box
 +
:*Change the amount of time in the '''Power Saving''' section to '''Never''' or a '''longer period of time'''
 +
:*Close the ''Settings'' Dialog box.
  
{{Admon/important|Using Superuser Privilege|Throughout this course, you may need to execute commands using the privileges of the the administrative user (username "root", also called the "superuser"). To switch from your account to the root account, type the command: <code>su</code>
 
  
After switching user notice and make note of the change in your shell prompt. Also note the difference in output for the <code>whoami</code> and<code>pwd</code> commands.
+
<ol><li value="14">Proceed to Investigation 2 to obtain basic information from your newly installed Centos Host machine.</li></ol>
  
'''Whenever this is required, make a note of it, and determine why superuser privilege is required.'''
+
'''Answer Investigation 1 observations (all parts and questions) in your lab log book.'''
  
When you are finished using the root account type exit to return to your previous account. '''Avoid using the superuser account unless absolutely necessary, because the superuser account has unlimited privilege and a typo can destroy your system.'''
 
  
In some documentation, you may see the command <code>su -</code> used in place of <code>su</code>. The dash argument causes <code>su</code> to go through the steps that would normally be performed when the root user logs in, including (1) running the startup scripts (such as<code>/etc/profile</code> and <code>/root/.bash_profile</code> and (2) changing to the root user's home directory (<code>/root</code>).
+
=INVESTIGATION 2: OBTAINING HOST MACHINE SYSTEM INFORMATION=
  
Note that the root user's home directory (<code>/root</code>) is ''not'' the same as the root directory of the system (<code>/</code>). It is also in a different directory than the rest of the home directories, which are typically in <code>/home</code> -- the reason for this is that <code>/home</code> is sometimes on a network filesystem shared by another server (as is the case on Matrix), and it's important that the system administrator be able to log in to the system even if the network is not operating normally.
 
}}
 
  
 
==Part 1: Obtaining Package Management / Package Information==
 
==Part 1: Obtaining Package Management / Package Information==
  
 +
{|width="40%" align="right" cellpadding="10"
 +
|- valign="top"
 +
|
 +
{{Admon/important|Accessing the Administration Account (root)| Many administrative tasks require the root administrative account. There are many ways to access this administration account:<ul><li>Login: '''root'''  (enter root password)</li><li>Switch User to root (without login):<ul><li>'''su''': Remains in regular user's directory, does not run root's startup script(s).</li><li>'''su -''' : Changes to root's home directory (/root) and runs root's start script(s).</li></ul></li></ul>}}
 +
|}
 
Navigate through your Graphical CentOS system, '''locate and run a terminal program (in order to issue Linux commands). Issue and record the commands used and the output generated in each of the following steps:'''
 
Navigate through your Graphical CentOS system, '''locate and run a terminal program (in order to issue Linux commands). Issue and record the commands used and the output generated in each of the following steps:'''
  
# The name of the installation log file is <code>'''/root/install.log'''</code> -- It is an ASCII file (how can you be sure?) which can be viewed with the <code>'''less'''</code> command.  
+
#With older (ancient) versions of Linux, a user once may have been allowed to login to their graphical Linux system using '''root''' as their user-name and their root password. This has been determined to be a security risk and that option has been removed with many or all Linux operating systems.
 +
#Therefore, from this point onwards, you will be logging into your regular user account instead and issuing a command to login as the ''root'' user.
 +
#Refer to the Information box regarding how to access the admin account from the command line.
 +
#Issue the command <b><code><span style="color:#3366CC;font-size:1.3em;">su </span></code></b> Issue the '''pwd''' and '''whoami''' commands to confirm your directory pathname. When finished logout of this account.
 +
#Issue the command <b><code><span style="color:#3366CC;font-size:1.3em;">su - </span></code></b> Issue the '''pwd''' and '''whoami''' commands to confirm your directory pathname. What do you notice are the main differences between using '''su''' versus using '''su -''' ?
 +
# An installation log file called  <b><code><span style="color:#3366CC;font-size:1.2em;">/var/log/anaconda/packaging.log</span></code></b> has been created to record the installation of your c7host machine. This file is an ASCII file which can be viewed with the <b><code><span style="color:#3366CC;font-size:1.2em;">more</span></code></b> command.  
 
# You can make use of this file to determine how many packages have been installed: complete the following command to count the number of packages that are labelled "Installing" in the installation log file:
 
# You can make use of this file to determine how many packages have been installed: complete the following command to count the number of packages that are labelled "Installing" in the installation log file:
:: <code>'''grep ________________ ________________ | wc -l'''</code>
+
:: <b><code><span style="color:#3366CC;font-size:1.2em;">grep -i packaging /var/log/anaconda/packaging.log | wc -l'''</span></code></b>
 
<ol>
 
<ol>
  <li value="3">Using the <code>rpm</code> command: you can also use the following commands to list all the installed packages, and the total number of packages installed:</li>
+
  <li value="8">Issue that command displayed above. Does it work? If not, what account do you think you should be in? When you get the command working record this important information regarding commands and the admin account in your lab logbook.</li>
 +
<li>Using the <code>rpm</code> command: you can also use the following commands to list all the installed packages, and the total number of packages installed:</li>
 
</ol>
 
</ol>
:: <code>'''rpm -q -a'''</code>
+
::<b><code><span style="color:#3366CC;font-size:1.2em;">rpm -q -a'''</span></code></b>
:: <code>'''rpm -q -a | wc -l'''</code>
+
::<b><code><span style="color:#3366CC;font-size:1.2em;">rpm -q -a | wc -l'''</span></code></b>
:: <code>'''rpm -qa  | wc -l'''</code>
+
::<b><code><span style="color:#3366CC;font-size:1.2em;">rpm -qa  | wc -l'''</span></code></b>
 
<ol>
 
<ol>
  <li value="4">The <code>'''-q'''</code> option means query, and the <code>'''-a'''</code> option means all (in other words, query all installed software packages). Did you get the same number of packages from the above two methods?</li>
+
  <li value="10">The <code>'''-q'''</code> option means query, and the <code>'''-a'''</code> option means all (in other words, query all installed software packages). Did you get the same number of packages from the above two methods?</li>
  <li>Some of the files on your system were installed with the software packages, and some were created by system activity (for example, by creating your Learn account and by logging in). If you know the package name (from the <code>install.log</code>), you can list all the files that were installed from the package by using the following command:</li>
+
  <li>Some of the files on your system were installed with the software packages, and some were created by system activity (for example, by creating your Learn account and by logging in). If you know the package name (from the <code>packaging.log</code>), you can list all the files that were installed from the package by using the following command:</li>
 
</ol>
 
</ol>
:: <code>'''rpm -q -l package_name'''</code><br />(where '''package_name''' represents the name of the ''application'' or ''package'')
+
::<b><code><span style=" pointer-events:none;cursor:default;color:#3366CC;font-size:1.2em;">rpm -q -l gedit</span></code></b>
<ol>
+
 
<li value="6">This combines the <code>'''-q'''</code> (query) option with the <code>'''-l'''</code> (list filenames) option</li>
+
<ol><li value="12">Issue the following command to obtain the total number of files installed for gedit:<br><br></li></ol>
<li>You can pipe the outupt through <code>'''wc -l'''</code> to count the number of lines:</li>
+
::<b><code><span style=" pointer-events:none;cursor:default;color:#3366CC;font-size:1.2em;">rpm -ql gedit | wc -l</span></code></b>
</ol>
 
:: <code>'''rpm -ql package_name| wc -l'''</code>
 
 
<ol>
 
<ol>
  <li value="8">Using what you learned in steps 3, 4, and 7, get a count of the total number of files installed by all of the software packages on your system.</li>
+
  <li value="13">Using what you learned in steps 3, 4, and 7, get a count of the total number of files installed by all of the software packages on your system.</li><li>How can you explain why this number is a lot larger than the total number of packages installed? Record your answer in your lab logbook.
 
</ol>
 
</ol>
  
==Part2: Obtaining System and Network Information==
+
==Part2: Obtaining System Information==
  
<ol>
+
{|width="40%" align="right" cellpadding="10"
<li>To find out the name that you have assigned to your Linux system, enter the command:  <code>'''hostname'''</code></li>
+
|- valign="top"
<li>To find out the kernel version of your GNU/Linux workstation and the date it was created, enter the command:   <code>'''uname -rv'''</code></li>
+
|
<li>To find out all the system processes running on your GNU/Linux workstation, enter the command: <code>'''ps -ef'''</code></li>
+
{{Admon/important|Pathname for USB Stick|The default mount location has been changed in linux distributions newer than CentOS. So while we will get '''/media/usb-device-name''', in newer distributions you'll see '''/run/media/userloginid/usb-device-name'''}}
<li>To capture the list of all the system processes to a file called <code>'''ps.lst'''</code>, enter the command: <code>'''ps -ef > ps.lst'''''</code></li>
+
|}
</ol>
+
#To find out the name that you have assigned to your Linux system, enter the command:  <b><code><span style="color:#3366CC;font-size:1.2em;">hostname</span></code></b>
 +
#To find out the kernel version of your GNU/Linux workstation and the date it was created, enter the command:<br><b><code><span style="color:#3366CC;font-size:1.2em;">uname -rv</span></code></b>
 +
#To find out all the system processes running on your GNU/Linux workstation, enter the command: <b><code><span style="color:#3366CC;font-size:1.2em;">ps -ef</span></code></b>
 +
#We will now collect networking information for your installed system.
 +
#To check the network configuration settings obtained from the DHCP server, run the following commands, describing the output in your log book:
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">ifconfig</span></code></b>
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">route -n</span></code></b>
 +
:::<b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">nslookup</span></code></b> (at the ''nslookup'' prompt, enter the word '''server''' and record the output. Type exit to leave nslookup).
 +
<ol><li value="8">Find the following information in the output of the above commands:</li></ol>
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">MAC address</span></code></b> of the ethernet network interface
 +
:::<b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">Subnet mask</span></code></b>
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">The IP address </span></code></b> (assigned to you by the DHCP server)
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">The default gateway</span></code></b>
 +
::: <b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">The DNS nameserver</span></code></b>
 +
<ol><li value="9">Run the commands <b><code><span style="color:#3366CC;font-size:1.2em;">hostname</span></code></b>, <b><code><span style="color:#3366CC;font-size:1.2em;">uname -rv</span></code></b>, <b><code><span style="color:#3366CC;font-size:1.2em;">ps -ef</span></code></b>, <b><code><span style="color:#3366CC;font-size:1.2em;">ifconfig</span></code></b>, and <b><code><span style="color:#3366CC;font-size:1.2em;">route -n</span></code></b> redirecting the output to add to a file in root's home directory called <b><code><span style="color:#3366CC;font-size:1.2em;">system.txt</span></code></b>.</li><li>Copy the installation log file <code>'''/var/log/anaconda/packaging.log'''</code> and the file '''system.txt''' to a USB memory key, or '''scp''' to your matrix account as a backup.</li></ol>
  
{{Admon/important|Pathname for USB Stick|The default mount location has been changed in linux distributions newer than CentOS. So while we will get /media/usb-device-name, in newer distributions you'll see /run/media/userloginid/usb-device-name}}
 
  
<ol>
+
'''Answer the Investigation 2 observations / questions in your lab log book.'''
<li value="13">Copy the installation log file <code>'''/root/install.log'''</code> and the file '''ps.lst''' to a USB memory key, or '''scp''' to your matrix account as a backup.</li>
 
<li>View the section below to learn about and perform an update on your fresh CentOS install (you may have to find spare time to perform this install if you are running short on lab time). '''Do <u>not</u> proceed to Investigation 3 without performing an update'''.</li>
 
<li>The CentOS software is updated frequently to add features, fix bugs, and upgrade security. Perform a system update to get the latest versions of the packages installed: Start the Firefox web browser, turn off popup window blocking (select ''Edit>Preferences'', then select the Content tab and uncheck the box to Block Popups), then login to SeneNET. Open a terminal and type <code>su</code> to start a shell as root. Enter the command <code>yum update</code> This will download and install all of the packages that have been updated since the installation DVD image was created.  If you complete this command at Seneca it should run quite fast as Seneca College hosts a CentOS Repository mirror (a copy of all of the current CentOS packages, on a local web server).</li>
 
</ol>
 
  
 +
= INVESTIGATION 3: LOOKING AHEAD =
  
{{Admon/tip |Rusty Issuing Linux commands since ULI101?|To be an effective Linux administrator, you need to become comfortable on issuing Linux commands in a shell, and use resources to quickly learn how to properly formulate Linux commands...<br /><br />You can run the following online tutorials to practice (refresh) issuing Linux commands. These tutorials were designed for another course called "OPS435", but you can still use them for practice. Simply open a shell, SSH into the Matrix server (eg. ssh yourusername@matrix.senecac.on.ca) and run the following 4 tutorials (you can copy and paste these separate pathnames and run like a program):<br /><br />'''/home/ops435/tutorials/tutorial1<br />/home/ops435/tutorials/tutorial2<br />/home/ops435/tutorials/tutorial3<br />/home/ops435/tutorials/vi-tutorial'''<br /><br />You can also refer to the section above called '''Linux Command Online Reference''' to see how use use the following Linux commands to obtain the required information.}}
+
==Part 1: Disable SELinux and Perform Software Updates==
  
'''Answer the Investigation 2 observations / questions in your lab log book.'''
+
{|width="40%" align="right" cellpadding="10"
 +
|- valign="top"
 +
|
 +
{{Admon/important|SELinux|SELinux stands for '''Security-Enhanced Linux'''. It is a component that helps to better secure the system to protect against intrusion (hackers). SELinux is enabled upon the default install of CentOS. SELinux can be a good thing, if you take care of it and know how it works. For this course it is strongly recommended that you '''disable SELinux by default''' because we won't have the time to reconfigure it every time the labs make it necessary.}}
 +
|}
 +
# Disabling SELinux is quite simple, just edit the file '''/etc/selinux/config''' and set SELINUX to '''disable<u>d</u>'''.
 +
# Add additional text regarding disabling SELinux.
 +
#The CentOS software is updated frequently to add features, fix bugs, and upgrade security. Perform a system update to get the latest versions of the packages installed: Start the Firefox web browser, turn off popup window blocking (select '''Edit''', '''Preferences''', then select the '''Content''' tab and uncheck the box to '''Block Popups'''), then return to your web-browser, load a page, and when prompted, login to SeneNET.
 +
#Make certain that you have at least 30 minutes available in your lab-time prior to performing a system update. Never abort a system update since it may damage your system files and render your host mahcine inoperable!
 +
#Open a terminal and type <b><code><span style="color:#3366CC;font-size:1.2em;">su</span></code></b> to start a shell as root. Enter the command <b><code><span style=" pointer-events:none;cursor:default;color:#3366CC;font-size:1.2em;">yum update</span></code></b> This will download and install all of the packages that have been updated since the installation DVD image was created.  If you complete this command at Seneca it should run quite fast as Seneca College hosts a CentOS Repository mirror (a copy of all of the current CentOS packages, on a local web server).
  
  
# Your system may not be automatically connected to Seneca's network. Locate the network icon (on top right-hand panel). Click on that icon, and select
+
==Part 2: Automating Routine Tasks (Shell Scripting)==
'''system eth0'''
 
# Open a web-browser and log into Seneca's wired network. You will need to perform this set every time you start a new session with your computer to perform future labs.
 
#Open a shell terminal.
 
#To check the network configuration settings obtained from the DHCP server, run the following commands, describing the output in your log book:
 
#* '''ifconfig'''
 
#* '''route -n'''
 
#* '''nslookup''' (at the > prompt, enter the word "server" (do not type the quotes) and record the output. Type exit to leave nslookup).
 
# Find the following information in the output of the above commands:
 
#* '''MAC address''' of the ethernet network interface
 
#* '''Subnet mask'''
 
#* '''The IP address''' assigned to you by the DHCP server
 
#* '''The default gateway'''
 
#* '''The DNS nameserver'''
 
  
'''Answer the Investigation 3 observations / questions in your lab log book.'''
+
{|width="40%" align="right" cellpadding="10"
 +
|- valign="top"
 +
|
 +
{{Admon/tip|Bash Shell Scripting Tips:|<br><ul><li>'''She-bang line: #!/bin/bash'''<br><br>Shell scripts have evolved of the past 40 years. To avoid running a newer shell script on an older shell, it is recommended to force running the shell script in the correct shell. In order to do this, on the first line at the very beginning of the shell script, you add the '''#!''' ('''# as in "shhhh" - a comment''', and''' ! is referred to as "bang" run a commmand''': in this case, '''run the command: /bin/bash'''). You can issue the Linux command '''which bash''' to get the correct location. If there is no bash shell on that machine, the shell script will not run (as a precaution - the Linux admin will know how to make a fix to the shell script if required).<br> </li><li>'''Variables:'''<br><br> There are 3 types of variables that can be used in shell scripting: '''ENVIRONMENT''' (eg. $USER), '''user-defined''' ($varName), and '''positional parameters''' (eg. $1, $2... containing arguments after shell script or by using set command (eg. '''set $(ls)''' ). Using dollar sign ('''$''') in front of variable expands the value assigned.<br><br></li><li>'''Command Substitution:'''<br><br>A very useful trick to take output from a command to be used as an argument for another command. Examples include:<br>'''file $(ls)'''<br>'''set $(ls);echo $#;echo $*'''<br>'''echo "hostname: $(hostname)"'''<br><br><li>'''Logic Control Flow Statements:'''<br><br>The '''test''' command can be used to see if a condition is true or false<br>(i.e. test $USER &#61; "root") . The '''$?''' special shell variable stores the result (zero if true, non-zero if false). Square brackets '''[ ]''' can be used to represent the test command with the condition <u>inside</u> the brackets (spaces separating brackets).Can use '''if''' / '''if-else''' / '''if-elif-else''' statements with brackets. The '''exit''' command can be used to terminate the shell script with a false value.<br><br>'''<u>Examples</u>'''<br><br>''if [ $USER &#61; "root" ]''<br>''then''<br>&nbsp;''echo "You must be root" >&amp;2''<br>&nbsp;''exit1''<br>''fi''<br><br># For number comparison: use:<br># -gt,-ge, -lt, -le, -eq, -ne<br><br>''if [ $age -gt 65 ]''<br>''then''<br>&nbsp;''echo "retire"''<br>''else''<br>&nbsp;''echo "don't retire"''<br>''fi''<br><br>''if [ $grade -gt 79 ]''<br>''then''<br>&nbsp;''echo "You get Good Mark"''<br>''elif [ $grade -gt 49 ]''<br>''then''<br>&nbsp;''echo "You pass"''<br>''else''<br>&nbsp;''echo "You fail"''<br>''fi''<br></li></ul>}}
 +
|}
 +
You may have learned about creating and running Bash Shell Scripts in your ULI101 course. Shell scripts help Linux users and system administrators to automate repetitive tasks to become more efficient and to help them save time. You will be reviewing and building a basic Bash Shell script to generate information reports for your newly-installed Linux host machine. Take time to view Shell Scripting Tips which are located on the right-hand side.
  
= INVESTIGATION 3: LOOKING AHEAD =
+
If you require <u>'''additional practice'''</u> in creating shell scripts and using the vi text editor, run the commands in your '''Matrix''' account: <ul><li>'''/home/murray.saul/vi-tutorial'''</li><li>'''/home/murray.saul/scripting-1'''</li></ul>
  
==Part 1: Disable SELinux==
+
Perform the following steps in your '''c7host''' machine:
  
{{Admon/important|SELinux|SELinux stands for '''Security-Enhanced Linux'''. It is a component that helps to better secure the system to protect against intrusion (hackers). SELinux is enabled upon the default install of CentOS. SELinux can be a good thing, if you take care of it and know how it works. For this course it is strongly recommended that you '''disable SELinux by default''' because we won't have the time to reconfigure it every time the labs make it necessary.}}
+
# Make certain to log out of your root account and remain as a regular user.
 +
# Open a Shell terminal and use a text editor (such as <b><code><span style="color:#3366CC;font-size:1.2em;">vi</span></code></b> or <b><code><span style="color:#3366CC;font-size:1.2em;">nano</span></code></b>) to create a Bash Shell script called: <b><code><span style="color:#3366CC;font-size:1.2em;">myreport.bash</span></code></b> in your current directory.
 +
# Copy and paste the text below into your vi editing session for your file report.bash<br> (how do you copy and paste efficiently in Linux?)<br>
  
# Disabling SELinux is quite simple, just edit the file '''/etc/selinux/config''' and set SELINUX to disabled.
+
<code style="color:#3366CC;font-family:courier;font-size:.9em;margin-left:20px;">
 
+
<br>
==Part 2: Automating Routine Tasks (Shell Scripting)==
+
&#35;!/bin/bash<br>
 +
<br>
 +
&#35; Author: *** INSERT YOUR NAME ***<br>
 +
&#35; Date:  *** CURRENT DATE ***<br>
 +
&#35;<br>
 +
&#35; Purpose: Creates system info report<br>
 +
&#35;<br>&#35; USAGE: ./myreport.bash<br>
 +
<br>
 +
if [ $USER != "root" ]  # only runs if logged in as root<br>
 +
then<br>&nbsp;echo "You must be logged in as root." >&2<br>
 +
&nbsp;exit 1<br>
 +
fi<br>
 +
</code>
 +
<br>
 +
<ol><li value="4">Save your editing session, assign the '''myreport.bash''' file read and execute permissions (at least for the owner) and run by typing:<br><b><code><span style="color:#3366CC;font-size:1.2em;">./myreport.bash</span></code></b></li><li>Did it run? If not what do you think you need to do in order to run the Bash Shell Script?</li><li>Issue the command <b><code><span style="color:#3366CC;font-size:1.2em;">su -</span></code></b> and run the script from the regular user's home directory (not root's home directory):<br><b><code><span style="color:#3366CC;font-size:1.2em;">~regularuserid/myreport.bash</span></code></b></li><li> Did it work?</li><li>Reopen your text-editing session for '''~regularuserid/myreport.bash''' and add the following lines of code to the bottom of the shell script file:</ol>
 +
<br>
 +
<code style="color:#3366CC;font-family:courier;font-size:.9em;">
 +
&#35; Create report title<br>
 +
<br>
 +
echo "SYSTEM REPORT" > /root/report.txt<br>
 +
echo "Date: $(date +'%A %B %d, %Y (%H:%M:%p)')" >> /root/report.txt<br>
 +
echo  >> /root/report.txt<br>
 +
</code>
 +
<br>
 +
<ol><li value="8">Save and run the bash shell script. View the contents of the file called '''report.txt''' that was generated (I hope you are using the up arrow key to issue previously issued commands in order to save time!). Notice how the redirection symbol &gt; is used at the beginning of the report, and then the other redirection symbol &gt;&gt; is used to help "grow" the report with the other content.</li><li>The only remaining content of the report would be the system information. We can use a shell scripting trick called "command substitution" $( .. ) in order place results from an command to be used by another command (like echo). Re-edit the shell script and add the following code at the bottom of the shell script file:</li></ol>
 +
<br>
 +
<code style="color:#3366CC;font-family:courier;font-size:.9em;">
 +
echo  >> /root/report.txt<br>
 +
echo "Hostname: $(hostname)"  >> /root/report.txt<br>
 +
echo  >> /root/report.txt<br>
 +
echo "Kernel Version: $(uname -rv)"  >> /root/report.txt<br>
 +
echo  >> /root/report.txt<br>
 +
</code>
 +
<br>
 +
<ol><li value="10">Save, run the script, and view the ''report.txt'' contents (are you using tip that was given to save time?).</li><li>Edit the shell script and include output from the <b><code><span style="color:#3366CC;font-size:1.2em;">ps aux</span></code></b> and <b><code><span style="color:#3366CC;font-size:1.2em;">ifconfig</span></code></b> commands (with appropriate titles). Remember to redirect that output to add to the bottom of the file!</li><li>Save, run and confirm that the shell script is working correctly.</li><li>What would be the use of keeping this shell script as a Linux system administrator?</li></ol>
 +
<ol><li value="14">Here are some more "complex" Bash Shell scripts, that perform the same task. Although you are not require to understand some of these other tricks, it is recommended that you view the contents of the scripts and save them for future consideration or exmaples.</li><li>The <b><code>wget</code></b> command can be used to quickly download files from the Internet. Issue the following command:<br><b><code><span  style="pointer-events: none;cursor: default;color:#3366CC;font-size:1.2em;">wget https://scs.senecac.on.ca/~murray.saul/text-report.bash</span></code></b></li><li>Verify that the file '''text-report.bash''' was downloaded to your current directory.</li><li>Assign read and execute permissions for this file by issuing the command: <b><code><span style="color:#3366CC;font-size:1.2em;">chmod u+rx text-report.bash</span></code></b></li><li>Run this Bash Shell script by issuing the command: <b><code><span style="color:#3366CC;font-size:1.2em;">./text-report.bash</span></code></b></li><li>Check to see if it created a report in your current directory. What is the purpose of the report?</li><li>Use the <b>vi</b> text editor to view the contents of the file <b>text-report.bash</b>. Can you understand how this script works?<br><br></li><li>Use the <b><code>wget</code></b> command to download, study, and run the following shell scripts on-line:<blockquote><b><code><span style=" pointer-events:none;cursor:default;color:#3366CC;font-size:1.2em;">https://scs.senecac.on.ca/~murray.saul/report.bash<br>https://scs.senecac.on.ca/~murray.saul/report3.bash</span></code></b></blockquote></li><li>Try to understand what these Bash Shell scripts do.</li><li>You have completed lab1. Proceed to Completing The Lab, and follow the instructions for "lab sign-off".</li></ol>
  
  
 +
'''Answer the Investigation 3 observations / questions in your lab log book.'''
  
  
= COMPLETING THE LAB / INSTRUCTOR SIGN-OFF =
+
= LAB 1 SIGN-OFF (SHOW INSTRUCTOR) =
[[Image:lab1_signoff.png|thumb|right|500px|Students should be prepared with a'''ll required commands (system information) displayed in a terminal (or multiple terminals) prior to calling the instructor for signoff'''.]]
+
[[Image:lab1_signoff.png|thumb|right|500px|Students should be prepared with '''all required commands (system information) displayed in a terminal (or multiple terminals) prior to calling the instructor for signoff'''.]]
 
'''Arrange evidence (command output) for each of these items on your screen, then ask your instructor to review them and sign off on the lab's completion:'''
 
'''Arrange evidence (command output) for each of these items on your screen, then ask your instructor to review them and sign off on the lab's completion:'''
  
:* '''Installed package count'''
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> Output of '''lsblk''' command showing correct partition names and sizes
:* Output of '''lsblk''' command showing correct partition names and sizes
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> Contents of '''/etc/fstab''' file confirming partitions file types are '''ext4'''
:* Correct '''IP address''' and '''MAC address'''
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> Correct '''IP address''' and '''MAC address'''
:* '''Default route (gateway)'''
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> '''Default route (gateway)'''
:* '''DNS name server IP Address'''
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> '''DNS name server IP Address'''
:* '''lab1 notes''' <u>and</u> '''first column of Comparison Chart in lab2'''.
+
::<span style="color:green;font-size:1.5em;">&#x2713;</span> Contents of your '''myreport.bash''' shell script
 +
::<span style="color:green;font-size:1.5em;">&#x2713;</span> proof of '''yum update''' performed on c7host
 +
::<span style="color:green;font-size:1.5em;">&#x2713;</span> '''SELinux''' is disabled on '''c7host'''
 +
::<span style="color:green;font-size:1.5em;">&#x2713;</span> '''lab1 notes''' <u>and</u> '''first column of Comparison Chart in lab2'''.
  
= ADDITIONAL PRACTICE =
+
== Practice For Quizzes, Tests, Midterm &amp; Final Exam ==
  
 
# How many packages were installed?
 
# How many packages were installed?
 
# How many files (correct to the nearest hundred) were installed?
 
# How many files (correct to the nearest hundred) were installed?
# How many users were created automatically on your system (do not count your learn account)?
+
# How many users were created automatically on your system (regular, admin)?
# What is your learn account's UID and GID?
+
# List 2 ways that you can access your root account
# What is your learn account's home directory?
+
# What is the difference between the commands '''su''' and '''su -''' ?
 
# What is the home directory for the user "root"?
 
# What is the home directory for the user "root"?
 
# How do you determine the host name of your GNU/Linux workstation?
 
# How do you determine the host name of your GNU/Linux workstation?
 
# What command can display the NIC's MAC address?
 
# What command can display the NIC's MAC address?
 +
# What command is used to get a list of running processes on your newly-installed system?
 +
# What is the command to copy files to your USB key?
 +
# How can Shell Scripts be used to help automate a task performed in lab1?
  
 
[[Category:OPS235]]
 
[[Category:OPS235]]
 
[[Category:OPS235 Labs]]
 
[[Category:OPS235 Labs]]

Latest revision as of 11:26, 24 September 2018

Stop (medium size).png
THIS IS AN OLD VERSION OF THE LAB
This is an archived version. Do not use this in your OPS235 course.

LAB PREPARATION

Purpose / Objectives of Lab 1

The c7host Linux server will run virtualization software to install and run 3 virtual machines (installed in lab2).

You need to install a Linux OS to be a host or "platform" to install and use other Linux VMs (Virtual Machines) during this course.

The Linux OS you will be installing in this lab will be a Host Machine (hostname: c7host) that will allow you to run Virtualization Software to create 3 separate virtual machines (to be performed in lab2). It is important to install this host machine correctly since other labs will depend on the stability of this host machine.


Main objectives:

  • Correctly install the CentOS 7 FULL INSTALL DVD (not LIVE DVD) on your removable hard disk.
  • Record installation characteristics of CentOS 7 FULL INSTALL in a chart (contained in lab2 logbook chart) to compare with other installation methods performed in lab2.
  • Verify correct settings prior to proceeding with host installation stages.
  • Obtain Linux server information after installation to create a software asset report for later access.
  • Disable Linux Kernel security enhancements to allow easier internal networking connections (to be reactivated in a later lab).
  • Observe that Bash Shell Scripts can automate routine tasks.


Minimum Required Materials

CentOS 7FULL INSTALL DVD
Removable Hard Disk Pack (SATA)
USB key
(for backups)
Lab Log Book
(labs 1 & 2)
Idea.png
Access to Instructions for Lab1
Since you will performing a full install on your computer, you cannot use that computer to simultaneously view instructions while you perform the full install. Here are some suggestions to make this process easier:
  • Printout Lab1 instructions at home prior to performing Lab1
  • Use a smart-phone, notebook, or netbook computer to view lab instructions (highly recommended)
  • If lab space availability is not an issue, use another computer termimal to view lab instructions while performing install
  • Follow step-by-step instructions from your OPS235 instructor (if demonstrated by instructor)


My Toolkit (CLI Reference)

Package Management

rpm
yum

System Information

hostname
uname
ps
lsblk

Networking

ifconfig
netstat
route
nslookup

Miscellaneous

grep
wc
pwd
ls
more
file
wget
chmod
scp
vi

Idea.png
Online Hands-on Linux Tutorials (recommended)
The following online tutorial will allow you to practice Linux commands that you learned from ULI101 as well as essential shell scripting skills. Login to your Matrix account, and issue the pathnames to run the online tutorial in Matrix:
  • Using the vi Text Editor:
    /home/murray.saul/vi-tutorial
  • Linux Basics:
    /home/murray.saul/linux-basics
  • Shell Scripting - Part I (Scripting Basics):
    /home/murray.saul/scripting-1

INVESTIGATION 1: CREATE HOST MACHINE (c7host)

For the next 3 investigations, you will learn how to install your Centos Full DVD onto your removable hard disk. You will customize your install to setup several separate partitions:
  • / (The "root" partition)
  • /home (Store regular user accounts)
  • /var/lib/libvirt/images (store virtual machine images to be created in lab2)
  • swap partition (Virtual Memory)

Make certain to record your observations of this install in the comparison chart for c7host in your lab2 logbook.

Part 1: Start Installation

Host Machine Details:
  • Name: c7host
  • Boot media / Installation: CentOS7 Full Install DVD
  • Memory: 16GB
  • Disk space: 250GB (or higher)
  • CPUs: 1
Important.png
You're supposed to use this hard drive only for this course
But if you really need to use it for two courses, and the professor for the other (probably windows) course will allow it - ask your professor for help with partitioning.
comparison chart in lab2 logbook.
The Installation Summary screen provides flexibly when configuring to install on your computer.
  1. Refer to this listing of installation screenshots if you need a reference:
    [ installation screenshots ]
  2. Insert your removable SATA hard disk into the drive tray.
  3. Set your computer's drive selector switch to external (a.k.a position #4).
  4. Power up the computer and insert the CentOS 7 Installation DVD into the DVD drive, then power-off computer.
  5. Newer computer models are labelled HP Z230.

    NOTES:
    • If you are using the newer model, allow the computer to boot up (without pressing F10 key) to boot from DVD.
    • Refer to the comparison chart in lab2 lab logbook, and fill in various installation information for c7host while you perform the installation (such as time it took to perform a full install, installation options, etc).

  1. Power on the computer again, and after booting from the CD, select from the installation menu: Install Centos7.

    Note: If you experience unreadable display after you boot into your installed system, you can redo the install, but select from the install menu: Troubleshooting and then select Install in Basic Graphics Mode.

  2. Next, you will be prompted for a language. In the first screen, select language English with subselection English-Canada and then click the Continue button on the bottom right-hand screen.
  3. The Install Summary should now appear. This screen allows the installer to customize their Centos7 system prior to installation.
  4. Configure the following installation settings from the Install Summary Screen:

    DATE & TIME:
    • Click on the Map to select Toronto area (you may also select from the drop-down menu section)
    • Click the DONE button at the top-left corner to finish and return to the Installation Summary screen.

    NETWORK & HOSTNAME:
    • Select the default Ethernet connection and click the button on the top right-hand side to change the setting from OFF to ON.
    • At the bottom left-hand corner type the hostname: c7host (all lowercase letters)
    • Review your settings, then click the DONE button at the top-left corner to finish and return to the Installation Summary screen.

    SOFTWARE SELECTION:
    • Select the software packages labelled: Gnome Desktop
    • Click the DONE button at the top-left corner to finish and return to the Installation Summary screen.

  5. Although the Centos installtion program can provide suggestions on how to partition your hard disk, you will be customizing partitions for your hard disk. This custom partitioning is important since it will have consequences on future labs that you perform (especially for lab2).

    Proceed to Part 2 to customize your partitions.


Part 2: Custom Partitioning

Idea.png
Mount Points and Linux File System Types
Similar to other Operating Systems like windows fat / vfat / ntfs file system types, it is good to know a few common file system types in Linux for comparison:
  • xfs:   Newer filesystem (fast transfer rates for large files, Journaling)
  • ext4:   Newer filesystem supporting large files and Journaling (used in for this lab)
  • ext2:   Stable filesystem popular for databases (no journaling)
Carefully verify partition mount-names and sizes prior to proceeding with install. Check installation screenshots link for verification.
  1. From the installation summary screen, click Installation Destination.
  2. In the installation destination screen, select the destination option: I will configure partitioning and then click Done.
  3. The manual partitioning screen should appear.
  4. If you have used your hard disk for previous Linux (Centos) distributions, you should remove them. Click on the distribution, and for each partition, select the partition and click the remove button (minus sign) and confirm deletion.
  5. Change the option New mount points will use the following partition scheme from LVM to Standard Partition (you will not be using LVM for your c7host machine).
  6. Before you proceed with creating partitions, let's see the partitions that we need to create for our host computer:
    • Primary Partitions (ext4):
      • 30GB for / (i.e. "root")
      • 40GB for /home
      • 100GB for /var/lib/libvirt/images
    • Swap Partition:
      • 16GB (Note: "swap" must be selected from the drop down menu)

    NOTE: Remember that the sizes are recorded in MB (eg. 30 GB = 30000 MB) and you should multiply GB by a factor of 1024 to get the correct size.
    (eg. 30 GB x 1024 = 30720 MB)

  7. We will now create the root (/) partition. Click on the add button (plus) sign.
  8. In the Add a New Mount Point screen, select / as the mount-point (either by typing or selecting from drop-down menu), and enter 30720 in for partition size and click Add Mount Point button.
  9. You will return to the previous dialog box.
    For the / partition, change the file-system type from xfs to ext4 and make certain that the Device Type is set to Standard Partition (not LVM). You need to repeat this procedure for the /home and /var/lib/libvirt/images partitions as well).
  10. Repeat the same steps above for the /home partition and /var/lib/libvirt/images partition. You need to type the /var/lib/libvirt/images partition since it does not appear in the drop-down menu.
  11. Recheck each of the created partitions, and make certain that the file-system type is set to ext4 and the Device Type is set to Standard Partition.
  12. Finally, add a swap partition (Mount Point: swap) for 16 GB.
  13. Check that your partition settings are correct (you can ask your instructor or lab monitor to confirm), and then click Done (possibly twice) in order to proceed

    NOTE: If there is an error message associated with your created partitions, you may need to add a /boot/efi partition (as a new mount). The capacity should be: 2954MB (i.e. 2,954 MB). Once finished, click Done.

  14. A Summary of Changes screen will appear to show the partitioning operations that will be created. Click the Accept Changes and click Begin Installation in the Installation Summary screen to proceed with the installation.
  15. Start timing your host machine installation.

Part 3: Completing the Installation

This screen indicates that installation is complete. You should remove the install DVD and confirm Centos7 boots from your removable hard drive.
  1. During the installation process, you will required to create a root password (for administration access) and create a regular user account. Click on Root Password and enter your root password. Think of an appropriate password and record that password somewhere in case you forget! An indicator will appear to show you how secure your password is. Retype your root password and click Done (you may have to click Done twice if your password is not considered to be a strong password).
  2. You need to create a regular user account. This account will be used to graphical log into your host machine. It is never recommended to graphically log into a graphical Linux/Unix system as root. It is better to log into a regular user account, then run a command to login as root (you will learn how to do this later in this lab).
  3. Click User Creation and enter your full name, username, and an appropriate password (and confirm password). Click Done to finish (click twice if password is not considered to be a strong password).
  4. Remember to record this host installation information in the installation comparison chart in the lab2 logbook.
  5. When installation is complete, you will notice a message at the bottom of the screen stating: CentOS is now successfully installed and ready for you to use!
  6. Click the Reboot button. Your DVD will briefly open in the DVD drive bay. Make certain to remove this installation DVD so that Centos will boot from your hard drive.
  7. After the system reboots, a boot menu should briefly appear, then prompt the user to accept the License Information (this is only a one-time occurrence).
    In order to accept the license agreement, issue the following keystrokes:

    1 followed by ENTER (to select the license agreement prompt
    2 followed by ENTER (to accept the license agreement)
    c followed by ENTER (to save the selection)
    c followed by ENTER (a second time to continue booting into the system)

  8. The system should then graphically prompt the user to login with their regular user account. Click on your regular user account name and enter your regular user password.

  9. The last phase of the installation process should now run:
    • Confirm English as the default input source and click Next.
    • Skip the creation of online accounts by clicking Next.
    • Start using your installed Linux system by clicking Start Using CentOS Linux.

  10. Stop timing your installation and note the amount of time that your installation took to perform. Also take the time to fill in the c7host section of the installation comparison chart in your lab2 logbook.
  11. Open a web-browser and check to see if you can connect to the Internet.

Turn-Off Screen Saver Lock

Your system automatically enables a screen-saver application which is a useful security tool to prevent unauthorized viewing of information on a terminal after a certain amount of inactivity.
If you find this feature annoying and want to turn it off or adjust the idle time perform the following steps:
  • Click on your username at the top right-hand screen
  • Select Settings from the drop-down menu.
  • Click the Power icon located in the Settings Dialog Box
  • Change the amount of time in the Power Saving section to Never or a longer period of time
  • Close the Settings Dialog box.


  1. Proceed to Investigation 2 to obtain basic information from your newly installed Centos Host machine.

Answer Investigation 1 observations (all parts and questions) in your lab log book.


INVESTIGATION 2: OBTAINING HOST MACHINE SYSTEM INFORMATION

Part 1: Obtaining Package Management / Package Information

Important.png
Accessing the Administration Account (root)
Many administrative tasks require the root administrative account. There are many ways to access this administration account:
  • Login: root (enter root password)
  • Switch User to root (without login):
    • su: Remains in regular user's directory, does not run root's startup script(s).
    • su - : Changes to root's home directory (/root) and runs root's start script(s).

Navigate through your Graphical CentOS system, locate and run a terminal program (in order to issue Linux commands). Issue and record the commands used and the output generated in each of the following steps:

  1. With older (ancient) versions of Linux, a user once may have been allowed to login to their graphical Linux system using root as their user-name and their root password. This has been determined to be a security risk and that option has been removed with many or all Linux operating systems.
  2. Therefore, from this point onwards, you will be logging into your regular user account instead and issuing a command to login as the root user.
  3. Refer to the Information box regarding how to access the admin account from the command line.
  4. Issue the command su Issue the pwd and whoami commands to confirm your directory pathname. When finished logout of this account.
  5. Issue the command su - Issue the pwd and whoami commands to confirm your directory pathname. What do you notice are the main differences between using su versus using su - ?
  6. An installation log file called /var/log/anaconda/packaging.log has been created to record the installation of your c7host machine. This file is an ASCII file which can be viewed with the more command.
  7. You can make use of this file to determine how many packages have been installed: complete the following command to count the number of packages that are labelled "Installing" in the installation log file:
grep -i packaging /var/log/anaconda/packaging.log | wc -l
  1. Issue that command displayed above. Does it work? If not, what account do you think you should be in? When you get the command working record this important information regarding commands and the admin account in your lab logbook.
  2. Using the rpm command: you can also use the following commands to list all the installed packages, and the total number of packages installed:
rpm -q -a
rpm -q -a | wc -l
rpm -qa | wc -l
  1. The -q option means query, and the -a option means all (in other words, query all installed software packages). Did you get the same number of packages from the above two methods?
  2. Some of the files on your system were installed with the software packages, and some were created by system activity (for example, by creating your Learn account and by logging in). If you know the package name (from the packaging.log), you can list all the files that were installed from the package by using the following command:
rpm -q -l gedit
  1. Issue the following command to obtain the total number of files installed for gedit:

rpm -ql gedit | wc -l
  1. Using what you learned in steps 3, 4, and 7, get a count of the total number of files installed by all of the software packages on your system.
  2. How can you explain why this number is a lot larger than the total number of packages installed? Record your answer in your lab logbook.

Part2: Obtaining System Information

Important.png
Pathname for USB Stick
The default mount location has been changed in linux distributions newer than CentOS. So while we will get /media/usb-device-name, in newer distributions you'll see /run/media/userloginid/usb-device-name
  1. To find out the name that you have assigned to your Linux system, enter the command: hostname
  2. To find out the kernel version of your GNU/Linux workstation and the date it was created, enter the command:
    uname -rv
  3. To find out all the system processes running on your GNU/Linux workstation, enter the command: ps -ef
  4. We will now collect networking information for your installed system.
  5. To check the network configuration settings obtained from the DHCP server, run the following commands, describing the output in your log book:
ifconfig
route -n
nslookup (at the nslookup prompt, enter the word server and record the output. Type exit to leave nslookup).
  1. Find the following information in the output of the above commands:
MAC address of the ethernet network interface
Subnet mask
The IP address (assigned to you by the DHCP server)
The default gateway
The DNS nameserver
  1. Run the commands hostname, uname -rv, ps -ef, ifconfig, and route -n redirecting the output to add to a file in root's home directory called system.txt.
  2. Copy the installation log file /var/log/anaconda/packaging.log and the file system.txt to a USB memory key, or scp to your matrix account as a backup.


Answer the Investigation 2 observations / questions in your lab log book.

INVESTIGATION 3: LOOKING AHEAD

Part 1: Disable SELinux and Perform Software Updates

Important.png
SELinux
SELinux stands for Security-Enhanced Linux. It is a component that helps to better secure the system to protect against intrusion (hackers). SELinux is enabled upon the default install of CentOS. SELinux can be a good thing, if you take care of it and know how it works. For this course it is strongly recommended that you disable SELinux by default because we won't have the time to reconfigure it every time the labs make it necessary.
  1. Disabling SELinux is quite simple, just edit the file /etc/selinux/config and set SELINUX to disabled.
  2. Add additional text regarding disabling SELinux.
  3. The CentOS software is updated frequently to add features, fix bugs, and upgrade security. Perform a system update to get the latest versions of the packages installed: Start the Firefox web browser, turn off popup window blocking (select Edit, Preferences, then select the Content tab and uncheck the box to Block Popups), then return to your web-browser, load a page, and when prompted, login to SeneNET.
  4. Make certain that you have at least 30 minutes available in your lab-time prior to performing a system update. Never abort a system update since it may damage your system files and render your host mahcine inoperable!
  5. Open a terminal and type su to start a shell as root. Enter the command yum update This will download and install all of the packages that have been updated since the installation DVD image was created. If you complete this command at Seneca it should run quite fast as Seneca College hosts a CentOS Repository mirror (a copy of all of the current CentOS packages, on a local web server).


Part 2: Automating Routine Tasks (Shell Scripting)

Idea.png
Bash Shell Scripting Tips:

  • She-bang line: #!/bin/bash

    Shell scripts have evolved of the past 40 years. To avoid running a newer shell script on an older shell, it is recommended to force running the shell script in the correct shell. In order to do this, on the first line at the very beginning of the shell script, you add the #! (# as in "shhhh" - a comment, and ! is referred to as "bang" run a commmand: in this case, run the command: /bin/bash). You can issue the Linux command which bash to get the correct location. If there is no bash shell on that machine, the shell script will not run (as a precaution - the Linux admin will know how to make a fix to the shell script if required).
  • Variables:

    There are 3 types of variables that can be used in shell scripting: ENVIRONMENT (eg. $USER), user-defined ($varName), and positional parameters (eg. $1, $2... containing arguments after shell script or by using set command (eg. set $(ls) ). Using dollar sign ($) in front of variable expands the value assigned.

  • Command Substitution:

    A very useful trick to take output from a command to be used as an argument for another command. Examples include:
    file $(ls)
    set $(ls);echo $#;echo $*
    echo "hostname: $(hostname)"

  • Logic Control Flow Statements:

    The test command can be used to see if a condition is true or false
    (i.e. test $USER = "root") . The $? special shell variable stores the result (zero if true, non-zero if false). Square brackets [ ] can be used to represent the test command with the condition inside the brackets (spaces separating brackets).Can use if / if-else / if-elif-else statements with brackets. The exit command can be used to terminate the shell script with a false value.

    Examples

    if [ $USER = "root" ]
    then
     echo "You must be root" >&2
     exit1
    fi

    # For number comparison: use:
    # -gt,-ge, -lt, -le, -eq, -ne

    if [ $age -gt 65 ]
    then
     echo "retire"
    else
     echo "don't retire"
    fi

    if [ $grade -gt 79 ]
    then
     echo "You get Good Mark"
    elif [ $grade -gt 49 ]
    then
     echo "You pass"
    else
     echo "You fail"
    fi

You may have learned about creating and running Bash Shell Scripts in your ULI101 course. Shell scripts help Linux users and system administrators to automate repetitive tasks to become more efficient and to help them save time. You will be reviewing and building a basic Bash Shell script to generate information reports for your newly-installed Linux host machine. Take time to view Shell Scripting Tips which are located on the right-hand side.

If you require additional practice in creating shell scripts and using the vi text editor, run the commands in your Matrix account:
  • /home/murray.saul/vi-tutorial
  • /home/murray.saul/scripting-1

Perform the following steps in your c7host machine:

  1. Make certain to log out of your root account and remain as a regular user.
  2. Open a Shell terminal and use a text editor (such as vi or nano) to create a Bash Shell script called: myreport.bash in your current directory.
  3. Copy and paste the text below into your vi editing session for your file report.bash
    (how do you copy and paste efficiently in Linux?)


#!/bin/bash

# Author: *** INSERT YOUR NAME ***
# Date: *** CURRENT DATE ***
#
# Purpose: Creates system info report
#
# USAGE: ./myreport.bash

if [ $USER != "root" ] # only runs if logged in as root
then
 echo "You must be logged in as root." >&2
 exit 1
fi

  1. Save your editing session, assign the myreport.bash file read and execute permissions (at least for the owner) and run by typing:
    ./myreport.bash
  2. Did it run? If not what do you think you need to do in order to run the Bash Shell Script?
  3. Issue the command su - and run the script from the regular user's home directory (not root's home directory):
    ~regularuserid/myreport.bash
  4. Did it work?
  5. Reopen your text-editing session for ~regularuserid/myreport.bash and add the following lines of code to the bottom of the shell script file:


# Create report title

echo "SYSTEM REPORT" > /root/report.txt
echo "Date: $(date +'%A %B %d, %Y (%H:%M:%p)')" >> /root/report.txt
echo >> /root/report.txt

  1. Save and run the bash shell script. View the contents of the file called report.txt that was generated (I hope you are using the up arrow key to issue previously issued commands in order to save time!). Notice how the redirection symbol > is used at the beginning of the report, and then the other redirection symbol >> is used to help "grow" the report with the other content.
  2. The only remaining content of the report would be the system information. We can use a shell scripting trick called "command substitution" $( .. ) in order place results from an command to be used by another command (like echo). Re-edit the shell script and add the following code at the bottom of the shell script file:


echo >> /root/report.txt
echo "Hostname: $(hostname)" >> /root/report.txt
echo >> /root/report.txt
echo "Kernel Version: $(uname -rv)" >> /root/report.txt
echo >> /root/report.txt

  1. Save, run the script, and view the report.txt contents (are you using tip that was given to save time?).
  2. Edit the shell script and include output from the ps aux and ifconfig commands (with appropriate titles). Remember to redirect that output to add to the bottom of the file!
  3. Save, run and confirm that the shell script is working correctly.
  4. What would be the use of keeping this shell script as a Linux system administrator?
  1. Here are some more "complex" Bash Shell scripts, that perform the same task. Although you are not require to understand some of these other tricks, it is recommended that you view the contents of the scripts and save them for future consideration or exmaples.
  2. The wget command can be used to quickly download files from the Internet. Issue the following command:
    wget https://scs.senecac.on.ca/~murray.saul/text-report.bash
  3. Verify that the file text-report.bash was downloaded to your current directory.
  4. Assign read and execute permissions for this file by issuing the command: chmod u+rx text-report.bash
  5. Run this Bash Shell script by issuing the command: ./text-report.bash
  6. Check to see if it created a report in your current directory. What is the purpose of the report?
  7. Use the vi text editor to view the contents of the file text-report.bash. Can you understand how this script works?

  8. Use the wget command to download, study, and run the following shell scripts on-line:
    https://scs.senecac.on.ca/~murray.saul/report.bash
    https://scs.senecac.on.ca/~murray.saul/report3.bash
  9. Try to understand what these Bash Shell scripts do.
  10. You have completed lab1. Proceed to Completing The Lab, and follow the instructions for "lab sign-off".


Answer the Investigation 3 observations / questions in your lab log book.


LAB 1 SIGN-OFF (SHOW INSTRUCTOR)

Students should be prepared with all required commands (system information) displayed in a terminal (or multiple terminals) prior to calling the instructor for signoff.

Arrange evidence (command output) for each of these items on your screen, then ask your instructor to review them and sign off on the lab's completion:

Output of lsblk command showing correct partition names and sizes
Contents of /etc/fstab file confirming partitions file types are ext4
Correct IP address and MAC address
Default route (gateway)
DNS name server IP Address
Contents of your myreport.bash shell script
proof of yum update performed on c7host
SELinux is disabled on c7host
lab1 notes and first column of Comparison Chart in lab2.

Practice For Quizzes, Tests, Midterm & Final Exam

  1. How many packages were installed?
  2. How many files (correct to the nearest hundred) were installed?
  3. How many users were created automatically on your system (regular, admin)?
  4. List 2 ways that you can access your root account
  5. What is the difference between the commands su and su -  ?
  6. What is the home directory for the user "root"?
  7. How do you determine the host name of your GNU/Linux workstation?
  8. What command can display the NIC's MAC address?
  9. What command is used to get a list of running processes on your newly-installed system?
  10. What is the command to copy files to your USB key?
  11. How can Shell Scripts be used to help automate a task performed in lab1?