Difference between revisions of "X-Gene Information"
Chris Tyler (talk | contribs) (Created page with 'Basic information about the X-Gene Servers == Boot Software == The systems ship with uBoot in SPI flash with console on serial /dev/ttyS0 at 115200/8/n/1 == Default Linux Inst…') |
Chris Tyler (talk | contribs) (→IP Information) |
||
| (8 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Category:Enterprise Hyperscale Lab]] | ||
Basic information about the X-Gene Servers | Basic information about the X-Gene Servers | ||
| Line 5: | Line 6: | ||
The systems ship with uBoot in SPI flash with console on serial /dev/ttyS0 at 115200/8/n/1 | The systems ship with uBoot in SPI flash with console on serial /dev/ttyS0 at 115200/8/n/1 | ||
| − | == Default Linux Installation == | + | == Default Linux Installation (Factory Image) == |
User/pass: root/root | User/pass: root/root | ||
| + | |||
User/pass: default/NULL | User/pass: default/NULL | ||
| Line 17: | Line 19: | ||
With the default Linux installation: | With the default Linux installation: | ||
| − | eth0: 1GBE upper-right corner (above USB ports) | + | * eth0: 1GBE upper-right corner (above USB ports) |
| − | eth1: 1GBE lower-left corner | + | * eth1: 1GBE lower-left corner |
| − | eth2: 1GBE upper-left corner | + | * eth2: 1GBE upper-left corner |
| − | eth3: 10GBE sfp+ | + | * eth3: 10GBE sfp+ |
| − | All four ports have been confirmed to work. <code>iperf</code> reports 9.41 | + | All four ports have been confirmed to work. <code>iperf</code> reports 9.41 Gb/s on the 10GBE port when directly connected to another X-Gene. |
| − | == | + | == IP Information == |
| − | + | These machines are currently connected to Iraq, with static IPs on the eth0 mac addresses. | |
| − | + | Iraq has the corresponding hostnames ''red'', ''blue'', and ''green'' assigned in /etc/hosts (these names match the original ethernet cable colours, though red is not used within the [[EHL]] because it is reserved for serial connections). | |
| − | + | The serial console port of each system is connected to the [[Cyclades Terminal Server]]. | |
Latest revision as of 15:27, 12 September 2014
Basic information about the X-Gene Servers
Contents
Boot Software
The systems ship with uBoot in SPI flash with console on serial /dev/ttyS0 at 115200/8/n/1
Default Linux Installation (Factory Image)
User/pass: root/root
User/pass: default/NULL
~800MB
IP Address is preset to 10.x.x.x
Ethernet port assignments
With the default Linux installation:
- eth0: 1GBE upper-right corner (above USB ports)
- eth1: 1GBE lower-left corner
- eth2: 1GBE upper-left corner
- eth3: 10GBE sfp+
All four ports have been confirmed to work. iperf reports 9.41 Gb/s on the 10GBE port when directly connected to another X-Gene.
IP Information
These machines are currently connected to Iraq, with static IPs on the eth0 mac addresses.
Iraq has the corresponding hostnames red, blue, and green assigned in /etc/hosts (these names match the original ethernet cable colours, though red is not used within the EHL because it is reserved for serial connections).
The serial console port of each system is connected to the Cyclades Terminal Server.
