Difference between revisions of "Winter 2010 Posters/SheevaPlug Configuration"
(Created page with ' = Project Name = SheevaPlug Configuration = Names = Alex Vlahopoulos = The SheevaPlug Hardware Specifications = '''Sheeva CPU Core''' 1.2 GHz operation L1 Cache: 16K Inst...') |
|||
| Line 1: | Line 1: | ||
| − | |||
= Project Name = | = Project Name = | ||
| Line 51: | Line 50: | ||
= The Goal = | = The Goal = | ||
| − | The goal of this project was to successfully run Fedora 12 on the SheevaPlug. | + | The goal of this project was to successfully run Fedora 12 on the SheevaPlug. The operating system that came loaded on the device is Debian. The purpose behind installing Fedora 12 on this device is to test the operating system's performance on the ARM architecture. |
= Challenges = | = Challenges = | ||
1. 512MB NAND is too small to install a regular installation of Fedora 12 on (The plug has no disk) | 1. 512MB NAND is too small to install a regular installation of Fedora 12 on (The plug has no disk) | ||
| + | |||
2. The plug does not have a BIOS | 2. The plug does not have a BIOS | ||
| Line 61: | Line 61: | ||
1. In order to run Fedora 12 on the SheevaPlug I had to install the operating system on an SD card (although it can also be installed on a USB drive). | 1. In order to run Fedora 12 on the SheevaPlug I had to install the operating system on an SD card (although it can also be installed on a USB drive). | ||
| + | |||
2. Since there is no BIOS to select which device gets booted, the SheevaPlug has a bootloader called U-boot. However, U-boot needed to be upgraded and configured for the SD card to be selected during the boot up process. | 2. Since there is no BIOS to select which device gets booted, the SheevaPlug has a bootloader called U-boot. However, U-boot needed to be upgraded and configured for the SD card to be selected during the boot up process. | ||
| + | = Results = | ||
| + | |||
| + | 1. Fedora 12 was successfully installed on an SD card and booted from the SheevaPlug. The boot up time was quick as well, with minimal extra configuration required once booted it up (i.e. networking) | ||
| + | |||
| + | 2. Following the HOW-TO page for upgrading U-boot was pretty simple, however making sure the uboot.bin file copies over to the USB drive is important for the device to actually read it and copy it over. To configure U-boot, about 7 configuration commands were required, as soon as this was done and the device rebooted, the device selected the SD card and booted Fedora 12. | ||
= Acknowledgements = | = Acknowledgements = | ||
| Line 76: | Line 82: | ||
*GlobalScale - http://www.globalscaletechnologies.com/p-22-sheevaplug-dev-kit-us.aspx | *GlobalScale - http://www.globalscaletechnologies.com/p-22-sheevaplug-dev-kit-us.aspx | ||
| − | *U-Boot Upgrading ( | + | *U-Boot Upgrading (HOW-TO-PAGE)- http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html |
= Logos = | = Logos = | ||
Revision as of 21:40, 16 April 2010
Contents
Project Name
SheevaPlug Configuration
Names
Alex Vlahopoulos
The SheevaPlug Hardware Specifications
Sheeva CPU Core
1.2 GHz operation
L1 Cache: 16K Instruction + 16K Data
L2 Cache: 256KB
Memory
DDR2 400MHz, 16-bit bus
512MB DDR2: 1Gb x8, 4 devices
Power efficient Samsung devices
NAND FLASH Controller, 8-bit bus
512MB NAND FLASH: 4Gb x8, direct boot
128-bit eFuse Memory
Power
Power input: 100-240VAC/50-60Hz 19W DC Consumption: 5V/3.0A High efficiency POL DC-DC converters
Development Interface
System Development Board JTAG and Console Interface via USB SDIO expansion JTAG OpenOCD support via USB
High Speed I/O & Peripherals
GE, USB 2.0 Host RTC w/ Battery
The Goal
The goal of this project was to successfully run Fedora 12 on the SheevaPlug. The operating system that came loaded on the device is Debian. The purpose behind installing Fedora 12 on this device is to test the operating system's performance on the ARM architecture.
Challenges
1. 512MB NAND is too small to install a regular installation of Fedora 12 on (The plug has no disk)
2. The plug does not have a BIOS
Solutions
1. In order to run Fedora 12 on the SheevaPlug I had to install the operating system on an SD card (although it can also be installed on a USB drive).
2. Since there is no BIOS to select which device gets booted, the SheevaPlug has a bootloader called U-boot. However, U-boot needed to be upgraded and configured for the SD card to be selected during the boot up process.
Results
1. Fedora 12 was successfully installed on an SD card and booted from the SheevaPlug. The boot up time was quick as well, with minimal extra configuration required once booted it up (i.e. networking)
2. Following the HOW-TO page for upgrading U-boot was pretty simple, however making sure the uboot.bin file copies over to the USB drive is important for the device to actually read it and copy it over. To configure U-boot, about 7 configuration commands were required, as soon as this was done and the device rebooted, the device selected the SD card and booted Fedora 12.
Acknowledgements
Chris Tyler
Links
- Fedora Project - http://fedoraproject.org/wiki/Architectures/ARM/PlatformSheevaplug
- Instructables (HOW-TO-PAGE) - http://www.instructables.com/id/How-to-install-Fedora-on-a-SheevaPlug-and-boot-off/
- U-Boot Upgrading (HOW-TO-PAGE)- http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html
Logos
- Fedora
- Seneca
